This document could not be shown here. Open the PDF.
Text of this document10 pages · 870 words
Page 1
Instruction Manual WAVFR Wired 10-Way Volt-Free Interface 2024 Version 2.0.0
Page 2
For programming system programming information: Wired system setup guide. For a general overview: Wired RAK application sheet. Contents 1WhatistheWAVFR? 2Inputs 3Installation 4AddingtheWAVFRasadevice 5Configuring the WAVFR 5.1 The Mapping Section 5.2 Inputs 5.3 Mapping Options 5.4 Input Action 1WhatistheWAVFR? TheWAVFRisa10-wayvoltfreeinterface which is programmable via Rasoft Pro using a WK-HUB. Each input can be programmed to its own Room and Channel, and each input has two states, ‘on make’ and ‘on break’ which can be configured to trigger a command for each state that the switch is in. Example: OnMake=Scene1 OnBreak=Off 2Inputs TheRakoWirednetworkhastwoconnectionoptions, either the RJ11 socket can be used with the supplied RJ11 cable, or a CAT5/CAT6 cable can be used on the daughterboard. Upto10volt-free inputs can be connected to the WAVFR. WAVFR Manual Version 2.0.0
Page 3
3Installation Installation should only be carried out by a competent electrician. STEP1 Removethecoverbyremoving the two screws at the bottom of the unit, pulling the bottom of the cover away from the bottom, andlifting it. Set the two cable clamps aside. STEP2 MakeaconnectiontotheRako Wired network via the RJ11 port using the supplied RJ11 cable, or by CAT5/CAT6 on the daughterboard on the top section of the WAVFR Connect the volt-free inputs to A-J, common wires can be connected to any of the three commoninputterminals. NB It is essential to set the correct termination on the daughterboard if it is used, for WAVFR Manual Version 2.0.0
Page 4
moreinformation, see Terminations. STEP3 Fit the supplied cable clamps andensure the cable is unable to move. STEP4 Replace the cover and replace the screws. 4AddingtheWAVFRasadevice Thefollowing steps assume: - AProject File has been created - Roomshavebeenadded - Channels have been added - AHUBoraRAMPIhasbeensetupasacommunicationsdevice If any of the above are still required, see the Wired system setup guide. - In Rasoft Pro, go to File > New Device WAVFR Manual Version 2.0.0
Page 5
- ADevicemenuwillpopup,selecttheWAVFRandselect‘Next’ - Give the WAVFR device a name and select ‘Next’ - Assign a Room and Channel and select ‘Next’ WAVFR Manual Version 2.0.0
Page 6
- To put the device into setup mode, press and hold the button on the top right of the WAVFR,andtheLEDwillbegintoflash.Releasethebutton;theLEDshould continue to flash, and the setup wizard will show ‘Device Found’ - Select ‘Finish’, the device is now paired and in the project file. 5ConfiguringtheWAVFR AWAVFRhasamaximumof24mapsthatcanbeset.Eachisprogrammablebyselectingit in the mappings list and then editing the three sections: “Inputs”, “Mapping Options” and “Output Action”. 5.1 The Mapping Section All programmed inputs for the Device must first have a mapping. The purpose of a mappingis to program an input to perform a specific command. Each input has its own letter to represent its input; the WAVFR has up to 10 inputs. Newmappingscanbecreatedbyselectingadisabledfieldandselecting the corresponding input letter in the next column. WAVFR Manual Version 2.0.0
Page 7
Active mappings can be copied or pasted into disabled mappings; this is typically used whenre-using similar functions of an existing mapping to save time such as a toggle function. 5.2 Inputs Theinputs for the mappings are configured in the Inputs section. Whenaninputishighlighted blue, it will set the corresponding input letter active in the mapping, selecting the input multiple times will cycle through the input options which are “Normal”, “Ignore” and “Invert”, an example can be seen below: ‘A - Normal’ creates a mapping for input A, ensuring that only one input is highlighted blue for each mapping. If A is set as ‘Invert’, the ‘On Make’ and ‘On Break’ commands will reverse. 5.3 Mapping Options Oncetheinputhasbeenselectedandconfigured,thebehaviouroftheinput is set up in the Mapping Options. WAVFR Manual Version 2.0.0
Page 8
Trigger on Make Whentheswitchinput makes contact, trigger the output command. Trigger on Break Whenaswitchbreaksits contact, trigger the output command. SendStopOnRelease Whenthemadecontactisreleased, a ‘Stop’ command will be triggered Trigger on Press Trigger the output command when the momentary switching makes contact between its input and common. Trigger on Release Trigger the output command when the momentary switch breaks contact between its input andcommon Don't update previous room If this box is ticked this map will not update the “last used” flag for both Room and Channel. When a “last used” is sent from this Device the most recent room and Channel sent which doesn't have “don't update previous Room” selected will be sent. WAVFR Manual Version 2.0.0
Page 9
Set Scenes only if lights are OFF: Thecommandsentinthe“outputaction”section is a scene that will only take effect if the lights are currently off. This is often used when the device interfacing with the WAVFR is a presence sensor. Anyinput Trigger (OR Logic): Useonly when combined inputs are required. 5.4 Input Action Room TheRoomnumberoftheoutputcommand. Channel TheChannelnumberoftheoutputcommandcanbeAllChannelsorasingleChannel. Disable map Whenenabled,thebuttoninput will have no output command. Scene If a Scene is being triggered, select a Scene between 1-16. Fade-Up/Fade-Down Commonlyusedtomanuallydimlightingupanddown,aswellastheOpening/Closingof Blinds. NB ‘Send Stop on Release’ should also be checked when using this option. MotorStop Usedtostop3rdpartymotorsthat are configured within the HUB. WAVFR Manual Version 2.0.0
Page 10
Ident This option is not recommended, as the command will make a load flash momentarily and provides no practical function for daily use. Toggle TheTogglefunction will alternate between two commands, either a Level command and Off, or a Scene command and Off. NB DonotmapmorethanoneToggletoasinglebuttonontheinputs;thiswillresult in sporadic switching due to toggles getting out of sync. Level Sets the lighting Level to a percentage of brightness between 0-100%. WAVFR Manual Version 2.0.0
Need assistance or looking to source this item?