This document could not be shown here. Open the PDF.
Text of this document6 pages · 1,795 words
Page 1
Radio Powr Savr LRFx-OCR2B-P, LRF2-VCR2B-P Wireless Occupancy/Vacancy Sensor 369480m 1 05.26.26 Radio Powr Savr Wireless Occupancy / Vacancy Ceiling Sensor Lutron Radio Powr Savr occupancy / vacancy sensors are wireless, battery-powered, passive infrared (PIR) sensors that automatically control lights via RF communication to compatible dimming and switching devices. These sensors detect the heat (IR radiation of 9.5 μm) from people moving within an area to determine when the Sensor Shown in White Sensor Shown in Black space is occupied. The sensors then wirelessly transmit the appropriate commands to the associated dimming and switching devices to turn the lights on or off automatically. They combine both convenience and exceptional energy savings potential along with ease of installation. Features Models Available • Wireless occupancy sensor has 3 settings available: • LRF -OCR2B-P- Auto-On / Auto-Off, Auto-On Low-Light / Auto-Off, and Color Code Manual-On / Auto-Off Occupancy and Vacancy • Auto-On Low-Light feature will turn lights on automatically Frequency / Channel Code only if there is less than approximately 10 Lux (1 fc) of • LRF2-VCR2B-P- ambient light (feature not available in all systems, Color Code check the control spec for more details) • Vacancy-only model available to meet California (U.S.A.) Vacancy Only Title 24 requirements Available for Channel Code 2 Only • Uses Clear Connect technology • Passive infrared motion detection with exclusive Lutron Frequency / Channel Codes XCT Technology for fine motion detection 2 = 431.0 – 437.0 MHz (U.S.A., Canada, Mexico, Brazil) 2 2 2 3 = 868.125 – 869.850 MHz (Europe, U.A.E.) • 360˚ coverage ranges from 324 ft (30.2 m ) to 676 ft 2 (62.4 m ), depending on mounting height 4 = 868.125 – 868.4755 MHz (China, Singapore) • Simple and intuitive adjustments available for Timeout, 5 = 865.5 – 866.5 MHz (India) Auto-On, and Activity settings 6 = 312.3 – 314.8 MHz (Japan) • Supports advanced occupancy features, such as 7 = 433.05 – 434.79 MHz (Hong Kong, Macau) dependent occupancy groups and customizable occupied / unoccupied presets in some systems Color Code • Multiple sensors can be added for extended coverage. WH = White Refer to product specification submittal of receiving device 1 to determine system limits BL = Black • Lens illuminates during test mode to verify ideal locations Compatible RF Devices • Multiple ceiling-mount methods available for different • For use with Lutron products only ceiling materials • Supports simultaneous association with multiple Lutron 2 • Front accessible test buttons make programming easy Clear Connect devices and / or systems • 10-year battery life design • RoHS compliant 1 The lens of the sensor is white and the housing is black. 2 Contact Lutron Customer Service at www.lutron.com/support for frequency / channel code compatibility with your particular geographic region, and for integrating with other Lutron lighting and shading products. ® SPECIFICATION SUBMITTAL Page 1 Job Name: Model Numbers: Job Number:
Page 2
Radio Powr Savr LRFx-OCR2B-P, LRF2-VCR2B-P Wireless Occupancy/Vacancy Sensor 369480m 2 05.26.26 Specifications Regulatory RF Range • Lutron Quality Systems Registered to ISO 9001:2015 LRF2-, LRF3-, LRF4-, LRF5-, LRF7- Regulatory Approvals Local load controls must be located within 60 ft (18 m) LRF2- line-of-sight, or 30 ft (9 m) through walls, of a sensor. • cULus Listed LRF6- • FCC certified Local load controls must be located within 40 ft (12.2 m) • IC certified line-of-sight, or 23 ft (7 m) through walls, of a sensor. • Meets CA (U.S.A.) Energy Commission Title 24 Sensor Coverage Test requirements • Front accessible test button • COFETEL certified • Lens illuminates orange in response to motion during test • ANATEL certified mode and is visible from 60 ft (18 m) • SUTEL certified Wireless Communication Test LRF3- • Front accessible test button • CE marked • Turn associated loads on and off • UKCA Timeout Options • TDRA type approval • 1 minute* • CITC type approval • 5 minutes LRF4- • 15 minutes (default setting) • SRRC type approval • 30 minutes • iMDA registered Auto-On Options (Occupancy Versions Only) LRF5- • Enabled: Sensor turns lights ON and OFF automatically • WPC Type (default setting). LRF6- • Low Light: Sensor turns lights ON automatically only • 007YUUL0689 in low ambient light conditions; sensor turns lights OFF LRF7- automatically. • FCC • Disabled**: Lights must be turned ON manually from dimming or switching device; sensor turns lights OFF Power / Performance automatically. • Operating voltage: 3 V- Activity Options • Operating current: 14 μA nominal • Low Activity: (default setting) • Requires one CR 123 lithium battery • Medium Activity: • 10-year battery life • High Activity: • Non-volatile memory (saved changes are stored during power loss) * Intended for use in high-activity, briefly occupied areas only. ** During the 15-second grace period that begins when the lights are Environment automatically turned off, the lights will automatically turn back on in response to motion. This grace period is provided as a safety and • Temperature: 32 ˚F to 104 ˚F (0 ˚C to 40 ˚C) convenience feature in the event the lights turn off while the room is still • For indoor use only occupied, so that the user does not need to manually turn the lights back on. After 15 seconds, the grace period expires and the lights must be • Relative humidity: less than 90% non-condensing manually turned on. Warranty • Limited Warranty: www.lutron.com/warranty or call 1.844.LUTRON1 (USA/Canada) or 610.282.3800 (Others) for a printed copy. ® SPECIFICATION SUBMITTAL Page 2 Job Name: Model Numbers: Job Number:
Page 3
Radio Powr Savr LRFx-OCR2B-P, LRF2-VCR2B-P Wireless Occupancy/Vacancy Sensor 369480m 3 05.26.26 Installation Overview Mounting Sensor Setup Temporary mounting is optional to test sensor coverage • Sensor setup is available as a service by Lutron. For more and wireless communication before permanently installing information see the Sensor Layout and Tuning service the sensor. document (Lutron P/N 3601235). Drop Ceiling (Compressed Fiber Ceiling Tile) Sensor Placement The mounting wire is provided for both temporary and • To detect motion, the sensor requires line-of-sight of permanent mounting of the sensor to ceiling tiles. It is room occupants. The sensor must have an unobstructed designed to allow temporary mounting, testing, and view of the room. DO NOT mount behind or near tall repositioning (if necessary) of the sensor without cabinets, shelves, hanging fixtures, ceiling fans, etc. The damaging a ceiling tile. Once the final position of the sensor cannot see through glass objects such as patio- or sensor has been chosen, the mounting wire should shower doors. be twisted together to permanently secure the sensor • Hot objects and moving air currents can affect the in place. performance of the sensor. To ensure proper operation, Solid Ceiling (Drywall, Plaster, Concrete, or the sensor should be mounted at least 4 ft (1.2 m) away Wood) from HVAC vents and halogen or incandescent bulbs that • Temporary mounting: Ten (10) temporary mounting strips are below the ceiling line. can be purchased in the kit, L-CMDPIRKIT, for temporarily • The performance of the sensor depends on a temperature mounting and testing the sensor. differential between the ambient room temperature and • Permanent mounting: Screws and anchors (for drywall or that of room occupants. Warmer rooms may reduce the plaster) provided to mount the sensor. ability of the sensor to detect occupants. Recess-Mount • Devices emitting Radio Frequency (RF) energy can affect • Do not recess-mount sensor in a metal surface. the performance of sensors. To ensure proper operation, • Recess-mounting ring requires an opening of 3 in (76 mm) sensors should be mounted at least 4 ft (1.2 m) away from in diameter. devices that emit radio waves (e.g., microwave ovens, wireless routers, or other non-Clear Connect wireless • Recess-mounting ring secures internally to ceiling. Sensor devices). When using Clear Connect - Type X lamps or twists into the recess mounting ring and sits flush with fixtures, ensure sensor is mounted at a distance of 2 ft ceiling (see image below). (0.6 m) or greater from the lamp or fixture. • Recess-mounting ring purchased as a separate kit: • For additional information on placing sensors, please see L-CRMK-WH. the Occupancy / Vacancy Sensor Design and Application Guide (P/N 368-3197) located at www.lutron.com ® SPECIFICATION SUBMITTAL Page 3 Job Name: Model Numbers: Job Number:
Page 4
Radio Powr Savr LRFx-OCR2B-P, LRF2-VCR2B-P Wireless Occupancy/Vacancy Sensor 369480m 4 05.26.26 Dimensions 3.57 in 2.85 in (90.7 mm) (72.4 mm) 0.88 in (22.5 mm) 1.13 in (28.7 mm) ® SPECIFICATION SUBMITTAL Page 4 Job Name: Model Numbers: Job Number:
Page 5
Radio Powr Savr LRFx-OCR2B-P, LRF2-VCR2B-P Wireless Occupancy/Vacancy Sensor 369480m 5 05.26.26 Coverage Diagrams Per NEMA WD7 test method Ceiling 8 ft (2.4 m) Floor 15 ft 12 ft 9 ft 6 ft 3 ft 0 3 ft 6 ft 9 ft 12 ft 15 ft (4.6 m) (3.7 m) (2.7 m) (1.8 m) (0.9 m) (0.9 m) (1.8 m) (2.7 m) (3.7 m) (4.6 m) 18 ft × 18 ft (5.5 m × 5.5 m) maximum square coverage area when m ounted on an 8 ft (2.4 m) ceiling Sensor 13 ft (4.0 m) radius of coverage at floor when mounted on an 8 ft (2.4 m) ceiling Occupant Sensor Coverage Chart (for sensor mounted in center of room) Ceiling Height Maximum Square Coverage Area* 2 2 8 ft (2.4 m) 18 ft × 18 ft (5.5 m × 5.5 m) 324 ft (30.2 m ) 2 2 9 ft (2.7 m) 20 ft × 20 ft (6.1 m × 6.1 m) 400 ft (37.2 m ) 2 2 10 ft (3.0 m) 22 ft × 22 ft (6.7 m × 6.7 m) 484 ft (44.9 m ) 2 2 12 ft (3.7 m) 26 ft × 26 ft (7.9 m × 7.9 m) 676 ft (62.4 m ) * 12 ft (3.7 m) is the recommended maximum mounting height ® SPECIFICATION SUBMITTAL Page 5 Job Name: Model Numbers: Job Number:
Page 6
Radio Powr Savr LRFx-OCR2B-P, LRF2-VCR2B-P Wireless Occupancy/Vacancy Sensor 369480m 6 05.26.26 Lens Masking Whenever possible, the sensor should be installed in a location where it cannot view areas outside the intended space, such as hallways or adjacent rooms. If this situation cannot be avoided, portions of the lens may be masked to block the view of the sensor into undesired areas. Ten (10) PIR lens masks may be purchased in the kit, L-CMDPIRKIT. Lens sections Lens sections PIR lens mask shown in gray shown in white are sold separately are not masked masked with labels (L-CMDPIRKIT) Hallway falls within sensor’s coverage area. Lutron, Clear Connect, Radio Powr Savr, XCT and any related trade dress and logos are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries. All other product names, logos, and brands are property of their respective owners. ® SPECIFICATION SUBMITTAL Page 6 Job Name: Model Numbers: Job Number:
Need assistance or looking to source this item?