This document could not be shown here. Open the PDF.
Text of this document5 pages · 1,108 words
Page 1
HomeWorks® WIRED POWER MODULES Wallbox Power Module 048-011 1a 04.21.03 HomeWorks Wired DESCRIPTION Wallbox Power Module The HomeWorks Wallbox Power Module (HWI-WPM-6D) controls up to six zones of light. The HWI-WPM-6D will operate the following sources with a continuous Square Law dimming curve or on a full conduction non-dim basis: Incandescent, Tungsten Halogen, Magnetic Default Scene Low-Voltage Transformer, Neon/Cold Cathode, and Lutron Tu-Wire Electronic Status LED ® Fluorescent Dimming Ballasts. Default Scene Button The HWI-WPM-6D will operate the follow- ing sources with a continuous Square Law dimming curve through separate power interfaces: Electronic Low-Voltage Transformer, and HWI-WPM-6D Lutron Hi-Lume or ECO-10TM Electronic ® Fluorescent Dimming Ballasts. MODEL NUMBERS Wallbox Power Modules HWI-WPM-6D-120 6-zones, 120VAC HWI-WPM-6D-240 6-zones, 240VAC HWI-WPM-6D-230CE 6-zones, 230VAC CE Marked SPECIFICATION SUBMITTAL Page ® JOB NAME: MODEL NUMBERS: JOB NUMBER:
Page 2
HomeWorks® WIRED POWER MODULES Wallbox Power Module 048-011 2a 04.21.03 SPECIFICATIONS System Communications and Capacity Input Power • Low-voltage type Class 2/PELV wiring connects Wallbox Power Operating voltage: 120VAC, 220-240VAC (non CE), or 230VAC (CE) Modules to HomeWorks Wired Processor. 50/60Hz. • Each HomeWorks Wired Processor has three configurable links, each capable of directly controlling up to 8 Wallbox Power Load Capacity Modules and/or GRAFIK Eye Main Units. ® Model Input Zone Unit Connections Voltage Capacity Capacity HWI-WPM-6D-120 100-127VAC 25-800W/VA 2000W/VA Input Power HWI-WPM-6D-240 220-240VAC 40-1200W/VA 3000W/VA Capacity: Nine terminals for line-voltage wiring. Each terminal will 2 HWI-WPM-6D-230CE 230VAC 40-800W/VA 2300W/VA accept up to two #12 AWG (2.5mm ) wires. Key Design Features Class 2/PELV • Tested to withstand electrostatic discharge without damage or Capacity: One 4-pin removable terminal block. Each pin will accept 2 memory loss, in accordance with IEC 801-2. up to two #18 AWG (1.0mm ) wires. • Tested to withstand surge voltages without damage or loss of Environment operation, in accordance with IEEE C62.41-1991 Recommended Ambient operating temperature: Practice on Surge Voltages in Low-Voltage AC Power Circuits. 0-40°C, 32-104°F, 0-90% humidity, non-condensing. Indoor use • Compensates in real time for incoming line voltage variations: only. No visible flicker with +/-2% change in RMS voltage/cycle and Warranty +/-2% Hz change in frequency/second. • Provides 10-year power failure memory: Automatically restores • 8-Year Limited Warranty. lighting to levels prior to power interruption. • Installs in a 4-gang U.S. wallbox, 3-1/2 in. (89mm) deep recom- mended, 2-1/4 in. (57mm) deep minimum. (Lutron part number 241-400 may be used). • Has faceplate that snaps on with no visible means of attach- ment. MOUNTING Wallbox (Lutron part number 241-400 may be used.) Wallbox Power Module Faceplate SPECIFICATION SUBMITTAL Page ® JOB NAME: MODEL NUMBERS: JOB NUMBER:
Page 3
HomeWorks® WIRED POWER MODULES Wallbox Power Module 048-011 3a 04.21.03 DIMENSIONS Front View Side View 8 5/8 in. 3/8 in. (220mm) (8mm) 2-1/8 in. (54mm) 5 in. 5 in. (126mm) (126mm) Module Detail - Front View Address Switch Rotary Address Dial Operation (faceplate removed) (16-position rotary) Position Module Output / Purpose F 0 1 0 Internal relay ON, all Zones OFF DE 23 1-8 Address for normal operation C 4 9 Zone 1 Full ON, all others OFF B 65 A Zone 2 Full ON, all others OFF A E F 0 12 D 3 C 4 9 7 B 65 8 A98 7 B Zone 3 Full ON, all others OFF C Zone 4 Full ON, all others OFF D Zone 5 Full ON, all others OFF E Zone 6 Full ON, all others OFF F All Zones Full ON SPECIFICATION SUBMITTAL Page ® JOB NAME: MODEL NUMBERS: JOB NUMBER:
Page 4
HomeWorks® WIRED POWER MODULES Wallbox Power Module 048-011 4a 04.21.03 LINE VOLTAGE WIRING (120V, 240V) Pull power wiring from distribution panel and to light fixtures. Each line voltage terminal 2 can accept up to two #12 AWG (2.5mm ) wires. 2 Earth/Ground from Distribution Panel (1) #12 AWG (2.5mm ) Distribution Panel (2) #12 AWG (2) #12 AWG 2 2 (2.5mm) (2.5mm) Load 2 ZONE 2 ZONE 1 Load 1 Load 4 ZONE 4 CU WIREONLY ZONE 3 Load 3 Hot/Live Load 6 ZONE 6 ZONE 5 Load 5 CLASS 2 USA HOT/LIVE 1 2 3 4 CLASS 2 Hot/Live IEC Neutral PELV NEUTRAL (1) #12 AWG SSA 1 2 3 4 2 (2.5mm) Rear View of Wallbox Power Module Neutral (1) #12 AWG 2 (2.5mm) 230V (CE) MAINS VOLTAGE WIRING Pull power wiring from distribution panel and to light fixtures. Each line voltage terminal 2 can accept up to two #12 AWG (2.5mm ) wires. For phase-to-phase wiring, connect one phase to Hot/Live and the other phase to Neutral. When wired phase-to-phase, there is no air gap when the Wallbox Power Module is Off: the MCB(s) must be turned off when servicing the Wallbox Power Module or associated loads. Earth/Ground from Distribution Panel (1) #12 AWG (2.5mm2) Distribution Panel (2) #12 AWG (2) #12 AWG 2 2 (2.5mm) (2.5mm) Load 2 ZONE 2 ZONE 1 Load 1 Load 4 ZONE 4 ZONE 3 Load 3 Hot/Live Load 6 ZONE 6 ZONE 5 Load 5 PELV ONLY N Hot/Live 1 2 3 4 Neutral (1) #12 AWG SSA 1 2 3 4 L 2 (2.5mm) Rear View of Wallbox Power Module Neutral (1) #12 AWG 2 (2.5mm) SPECIFICATION SUBMITTAL Page ® JOB NAME: MODEL NUMBERS: JOB NUMBER:
Page 5
HomeWorks® WIRED POWER MODULES Wallbox Power Module 048-011 5a 04.21.03 LOW-VOLTAGE CLASS 2/PELV WIRING Pull low-voltage Class 2/PELV wiring for system com- Four wires for low-voltage Class2/PELV munications. 2 • Two #18 AWG (1.0mm ) for control wiring. 2 • Must be daisy-chained. • One shielded, twisted pair #18 AWG (1.0mm ) for data link. • Must be less than 2000 feet (610m). • Connection between #2 terminals is not made between Wallbox • Must run separately from line (mains) voltage wiring (minimum Power Modules, GRAFIK Eye Main Units, or the HomeWorks ® 1/4 in. (6.4mm) spacing). Processor. • Cable may be ordered from Lutron as GRX-CBL-346S-500. Rear View of Wallbox Power Module (120 V Version Shown) ZONE 2 ZONE 1 ZONE 4 CU WIREONLY ZONE 3 ZONE 6 ZONE 5 USA HOT/LIVE 1 2 3 4 CLASS 2 IEC SSA PELV NEUTRAL 1 2 3 4 Modules can be connected to any of these three links depending on the configuration of the HomeWorks Utility. Rear View of Wallbox Power Module (120 V Version Shown) ZONE 2 ZONE 1 ZONE 4 CU WIREONLY ZONE 3 ZONE 6 ZONE 5 USA HOT/LIVE 1 2 3 4 CLASS 2 IEC SSA 1 2 3 4 PELV NEUTRAL 2 Terminal 1 - 1 #18 AWG (1.0mm ) Terminals 3 & 4 - 1 pair #22-18 AWG (0.5 - Do not connect #2 terminal 2 1.0mm) twisted/shielded SPECIFICATION SUBMITTAL Page ® JOB NAME: MODEL NUMBERS: JOB NUMBER:
Need assistance or looking to source this item?