Lutron HomeWorks Universal DALI Power Module LQSE-2DALUNV-D – specification submittal (3691179c)

Page 1

HomeWorks LQSE-2DALUNV-D DALI® Power Module 3691179c 1 08.11.22 HomeWorks Universal DALI® Power Module (for regions outside of North America) 4 5 9 10 The DALI® Power Module unit is a DALI-2® certified 1 1 2 2 V V QS Ethernet DALI 1 DALI 2 3 Class 2L 3 4 Class 2L 4 DA 1 DA 2 ® ® IR NECIEC PE IR NEC® Class 2 DIN-rail mounted single master application controller 20 V ProgrammableCCIOccComCOM20 VNECIEC PEMan. OverrideOccCCIComCOMMUXMUXMUXMUX24 VCOMCOMIEC PELV Photo Photo +1.844.LUTRON1 HomeWorks Universal DALI Power Module Tc > 75 ºC Energi Savr Node QS +44.(0)20.7702.0657 LQSE-2DALUNV-D Z096+91.124.4390130 Test | Prueba QSNE-2DAL-D N1771 for use with DALI®-compliant digital addressable loads lutron.com Tester 230 V~ 50/60 Hz 100 mA 50

www.lutron.com

220–240 V~ 50/60 Hz 80 mA 120 V~ 50/60 Hz 120 mA 243C IND.CONT.EQ. lutron.com/ +44.(0)20.7680.4481 ChinaRohs in HomeWorks QSX and HomeWorks QS systems. It L N 60 ºC/75 ºC Cu Al 0,6 N•m (5.0 in-lb) 8,0 mm(5/16 in) provides DALI® bus power and control for two independent DALI® buses with up to 64 DALI®-compliant, V digital addressable loads on each bus. LQSE-2DALUNV-D D E Model Numbers LQSE-2DALUNV-D 1 Feature HomeWorks QSX HomeWorks QS DALI® single master application controller # of supported DALI® compliant buses 2 2 # of supported DALI® compliant loads per bus 64 64 # of Lutron zones per bus 64 16 Supports DALI® IEC62386-102 standard fade times X Fade time support of up to 4 hours Supports DALI® IEC62386-202 (Type 1) self-contained emergency loads X Supports DALI® IEC62386-209 (Type 8) tunable white (tc) loads 2 X Supports dual channel white tunable loads Supports perceived intensity control 3 X Simultaneous control of color and intensity with independent fade times 4 X Dynamic DALI® group allocation Field configurable system failure level, minimum / maximum levels, and fade times Power failure memory retains control unit programming in the event of power loss Lights remain unchanged during firmware upgrade 1 Available in HomeWorks version 15.11 or greater. 2 Dual channel white tunable load support has been replaced with Type-8 tunable white loads for HomeWorks QSX system. 3 Actual color temperature output is determined by the tolerance of the third-party driver. 4 Dynamic DALI® group allocation automatically and intelligently assigns zones to DALI® groups to maximize dimming performance and minimize asynchronous behavior of loads within a zone. DALI® Compatibility The Lutron HomeWorks Universal DALI® Power Module is DALI-2® certified by the Digital Illumination Interface Alliance® (DiiA®). In order to ensure compatibility with Lutron DALI® controllers, the connected DALI® LED drivers and fluorescent ballasts must be DALI-2® certified and marked. In addition to compatibility, it is important to select high-quality and high-performance LED drivers and fluorescent ballasts. DALI-2® certified devices are readily available from many manufacturers and are tested for compatibility with the standard. For a complete list of available DALI-2® certified devices, see the DiiA® website at https://www.digitalilluminationinterface.org/products. DALI® devices that are not listed on the DiiA® website and are not marked DALI-2® cannot be considered DALI-2® certified. The DALI® version-1 standard does not ensure compatibility. To apply the original DALI® version-1 mark on LED drivers and fluorescent ballasts, no verification of the test results was required, and manufacturers could self-declare compliance and apply the DALI® mark. If you would like to use an LED driver or fluorescent ballast that is not DALI-2® certified but carries a DALI® version-1 logo, Lutron recommends that these devices be tested to ensure compatibility. Lutron is able to perform this testing on request. Samples of the drivers and light engines must be submitted to Lutron and the expected turnaround time is 6 to 8 weeks after the drivers are received. Fees for testing may apply. Lutron recommends that this testing be performed before the fixtures and lighting controls are purchased and installed. Contact your Lutron sales representative for more information. 1 ®SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:

Page 2

HomeWorks LQSE-2DALUNV-D DALI® Power Module 3691179c 2 08.11.22 Typical Application HomeWorks Wallstation Power GRAFIK Module Eye QS Processor 800W Max5500W Max 00 W Max500 WMax CCI Zone 1ZZone 2 one 3Zone 4 Option Input D Def H HiTemp r Module Opt1 M we L Prog Po Opt2 il Ra Power DIN LQSE-4A-Opt3 230V~ 50 / 60 Hz 10 A www.lutron.com +44.(0)20.7702.0657 To QS QS Contact devices Closure Interface 7 QS Link Sivoia QS Shade / Drapery QS Power Supply UULL RRTT NNOO RR Programmable CCI and Manual Override CCI DA 1 Up to 64 UULL RRTT NNOO DALI-compliant, DA 2 Control gear Control gear digital addressable loads on each bus Control gear Control gear 45 910 1 2 1 2 2 2 LV LV QS Ethernet DALI 1 DALI 2 3 Class 3 4 Class 4 DA 1 DA 2 ® o Ic M ® o cI M X X M V IR NEC IEC PE m V IR m X X V NEC® Class 2 20 Programmable CCOc Co CO 20 NEC IEC PE Man. OverrideOcCC Co CO MU MU MUMU 24 COMCO IEC PELV 120 V~ / 220-240 V~ Phot Phot +1.844.LUTRON1 HomeWorks Universal DALI Power Module Tc > 75 ºC Energi Savr Node QS +44.(0)20.7702.0657 LQSE-2DALUNV-D Z096+91.124.4390130 Test | Prueba QSNE-2DAL-D N1771 lutron.com Control Power Tester 230 V~ 50/60 Hz 100 mA 50 www.lutron.com 220–240 V~ 50/60 Hz 80 mA 120 V~ 50/60 Hz 120 mA 243C IND.CONT.EQ. lutron.com/ +44.(0)20.7680.4481 ChinaRohs LN 60 ºC/75 ºC Cu Al 0,6 N•m (5.0 in-lb) 8,0 mm(5/16 in) LQSE-2DALUNV-D 2 ®SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:

Page 3

HomeWorks LQSE-2DALUNV-D DALI® Power Module 3691179c 3 08.11.22 Specifications Power DALI® Buses • LQSE-2DALUNV-D: 120 / 220-240 V~ 50 / 60 Hz, • The DALI® Power Module has an integrated bus power max 120 mA supply that provides a guaranteed current of 128 mA • Lightning strike protection meets ANSI / IEEE standard (maximum of 250 mA) to power each bus. 62.31-1980. Can withstand voltage surges of up to • The DALI® Power Module is a DALI® single master 6000 V~ and current surges of up to 3000 A controller and therefore no other controllers or sensors • DALI® Bus Output: 16 V- 128 mA guaranteed supply may exist on the same DALI® bus. current, 250 mA maximum supply current per bus • Some DALI® loads may be polarity sensitive; refer to individual manufacturers’ specifications for proper Standards connection to the DALI® bus. • Lutron Quality Systems registered to ISO 9001:2015. • Short circuit protection with automatic re-start • IEC 60669-2-5 (610 ms shutdown delay with a 3 second re-start ® certified - IEC 62386-101 and IEC62386-103 ed.2 followed by 800 ms shutdown delay with 160 ms • DALI-2 • NOM Certified retry time). • ICES-3(B) / NMB-3(B) Troubleshooting and Maintenance • FCC Part 15 Features • cULus Listed • UL® 924 • Maintains redundant memory of control gear Environment programming for ease of single- and multi-control gear replacement. • Ambient Temperature Operating Range: 0 ºC to 40 ºC • After installation, “TEST” button verifies DALI® wiring (32 ºF to 104 ºF) on all fixtures. • Relative humidity: less than 90% non-condensing. • For indoor use only. Terminals 2 2 • Mains wiring: 1.0 mm to 4.0 mm (18 AWG to 12 AWG) 2 2 • DALI® Bus Wiring: 0.5 mm to 4.0 mm

(20 AWG to 12 AWG) 2 2 • QS Link Wiring: 0.5 mm to 2.5 mm (20 AWG to 12 AWG) 2 2 • CCI and CCI Emergency Wiring: 0.5 mm to 1.5 mm (20 AWG to 16 AWG) Mounting • Intended to mount within an IP20 (minimum) rated consumer panel or breaker panel with integrated DIN rail and dead cover. • 9 DIN modules (161.7 mm). • For more information on mounting and installation in panels with integrated DIN rail see the DIN Rail Best Practices Application Note (P / N 048466) at www.lutron.com 3 ®SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:

Page 4

HomeWorks LQSE-2DALUNV-D DALI® Power Module 3691179c 4 08.11.22 Overview of Wiring Terminals and Mechanical Dimensions IEC PELV / NEC® Class 2 Programmable IEC PELV / CCI Manual NEC® Class 2 Override CCI QS 500-13431 Rev. B Z096 DALI® DALI® Link N1771 bus 1* bus 2* 1 2 3 4 5 6 7 8 9 0 4 5 9 10 1 1 2 2 V V QS Ethernet DALI 1 DALI 2 3 Class 2L 3 4 Class 2L 4 DA 1 DA 2 ® ® IR NECIEC PE IR NEC® Class 2 20 V ProgrammableCCIOccComCOM20 VNECIEC PEMan. OverrideOccCCIComCOMMUXMUXMUXMUX24 VCOMCOMIEC PELV 89.7 mm Photo Photo +1.844.LUTRON1 HomeWorks Universal DALI Power Module (3.5 in) Tc > 75 ºC Energi Savr Node QS +44.(0)20.7702.0657 LQSE-2DALUNV-D Z096+91.124.4390130 Test | Prueba QSNE-2DAL-D N1771 lutron.com Tester 230 V~ 50/60 Hz 100 mA 50

www.lutron.com

220–240 V~ 50/60 Hz 80 mA 120 V~ 50/60 Hz 120 mA 243C IND.CONT.EQ. lutron.com/ +44.(0)20.7680.4481 ChinaRohs L N 60 ºC/75 ºC Cu Al 0,6 N•m (5.0 in-lb) 8,0 mm(5/16 in) V 161.7 mm D E Mains (6.375 in) Wiring * Wire DALI® according to local codes 60.6 mm (2.375 in) 4 ®SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:

Page 5

HomeWorks LQSE-2DALUNV-D DALI® Power Module 3691179c 5 08.11.22 Wiring: Mains Voltage Wiring from Distribution to Bus Supply • Turn off breaker at distribution panel. 4 5 9 10 1 1 2 2 V V QS Ethernet DALI 1 DALI 2 3 Class 2L 3 4 Class 2L 4 DA 1 DA 2 ® ® IR NECIEC PE IR NEC® Class 2 20 V ProgrammableCCIOccComCOM20 VNECIEC PEMan. OverrideOccCCIComCOMMUXMUXMUXMUX24 VCOMCOMIEC PELV • Run line, neutral, and wires from a Photo Photo +1.844.LUTRON1 HomeWorks Universal DALI Power Module Tc > 75 ºC Energi Savr Node QS +44.(0)20.7702.0657 LQSE-2DALUNV-D Z096+91.124.4390130 Test | Prueba QSNE-2DAL-D N1771 line/hot feed to the DALI® Power Module. lutron.com Tester 230 V~ 50/60 Hz 100 mA 50 4 5 9 10 www.lutron.com

220–240 V~ 50/60 Hz 80 mA 120 V~ 50/60 Hz 120 mA 243C IND.CONT.EQ. lutron.com/ +44.(0)20.7680.4481 ChinaRohs L N 60 ºC/75 ºC Cu Al 0,6 N•m (5.0 in-lb) 8,0 mm(5/16 in) 1 1 2 2 V V QS Ethernet DALI 1 DALI 2 3 Class 2L 3 4 Class 2L 4 DA 1 DA 2 ® ® Emergency Lighting Applications IR IR NEC® Class 2 V NEC IEC PE ProgrammableCCIOcc ComCOM 20 V NEC IEC PE Man. OverrideOccCCID E ComCOM MUXMUX MUXMUX 24 V COM IEC PELV 20 V Photo Photo COM • Use normal (non-essential) power only. HomeWorks Universal DALI Power Module +1.844.LUTRON1 Tc > 75 ºC • When normal power drops out, the DALI® Power Energi Savr Node QS +44.(0)20.7702.0657 LQSE-2DALUNV-D Z096+91.124.4390130 Test | Prueba QSNE-2DAL-D Module will not power the DALI® buses. When this lutron.com N1771 Tester 230 V~ 50/60 Hz 100 mA 50 occurs, control gear powered from emergency www.lutron.com

220–240 V~ 50/60 Hz 80 mA 120 V~ 50/60 Hz 120 mA 243C IND.CONT.EQ. lutron.com/ +44.(0)20.7680.4481 ChinaRohs feeds go to their system failure level (full light output L N 60 ºC/75 ºC Cu Al 0,6 N•m (5.0 in-lb) 8,0 mm(5/16 in) by default). Mains Wiring and Low Voltage Separation • The DALI® Power Module is designed to separate mains wiring from PELV circuits. • Follow appropriate local and national codes to avoid V violating required separation guidelines. D E N 120 / 220-240 V~ L Distribution Panel – Earth / Ground N – Neutral L – Mains / Line 5 ®SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:

Page 6

HomeWorks LQSE-2DALUNV-D DALI® Power Module 3691179c 6 08.11.22 Wiring: DALI® Bus The DALI® Power Module will supply power to each DALI® bus independently. Each bus supports a 4 5 9 10 maximum of 64 DALI®-compliant, digital 1 1 2 2 V V QS Ethernet DALI 1 DALI 2 3 Class 2L 3 4 Class 2L 4 DA 1 DA 2 ® ® IR NECIEC PE IR NEC® Class 2 20 V ProgrammableCCIOccComCOM20 VNECIEC PEMan. OverrideOccCCIComCOMMUXMUXMUXMUX24 VCOMCOMIEC PELV addressable loads per bus. Photo Photo +1.844.LUTRON1 HomeWorks Universal DALI Power Module Tc > 75 ºC Energi Savr Node QS +44.(0)20.7702.0657 LQSE-2DALUNV-D Z096+91.124.4390130 Test | Prueba QSNE-2DAL-D N1771 lutron.com Tester 230 V~ 50/60 Hz 100 mA 50

www.lutron.com

220–240 V~ 50/60 Hz 80 mA 120 V~ 50/60 Hz 120 mA 243C IND.CONT.EQ. lutron.com/ +44.(0)20.7680.4481 ChinaRohs L N 60 ºC/75 ºC Cu Al 0,6 N•m (5.0 in-lb) 8,0 mm(5/16 in) DALI® Wiring • DALI® wiring is not SELV. V D E • DALI® wiring is treated as mains voltage, and thus DALI may be run within the same sheathing. ® ® DALI bus 1 bus 2 • Ensure that there is no greater than a 2 V drop DA 1 (-) DA 2 (+) between the DALI® Power Module and the end of DA 1 (+) DA 2 (-) the DALI® Bus. • Consult all national and local electrical codes for separation requirements. Maximum DALI®-compliant Wire Gauge Bus Wire Length * 2 1.5 mm (16 AWG) 300 m (984 ft) 2 0.75 mm (20 AWG) 150 m (492 ft) 2 0.50 mm (22 AWG) 100 m (328 ft) * Indicates the total length of DALI® wires. Assembled in MexicoNEC® Class 2 DA 1 DA 2 NEC® Assemblé aux Mexique Ensamblado en MéxicoMUXMUXCOMIEC PELV Class 2 HomeWorks QS Ta > 65 ºCLQSE-2DAL-D

Test | Prueba120 V~ 50 / 60 Hz 120 mA224433CC IINDND..CCOONNTT..EEQQ.. +1.844.LUTRON1 Tester230 V~ 50 / 60 Hz 80 mA +44.(0)20.7702.0657 lutron.com LNTa 65 °C65/75 ºC Cu Al5 in-lb (0,6 N•m) 5/16 in (8 mm) 6 ®SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:

Page 7

HomeWorks LQSE-2DALUNV-D DALI® Power Module 3691179c 7 08.11.22 Wiring: QS Link QS Link Wiring (IEC PELV/NEC® Class 2) • Link communicates using IEC PELV wiring. 4 5 9 10 1 1 2 2 V V QS Ethernet DALI 1 DALI 2 3 Class 2L 3 4 Class 2L 4 DA 1 DA 2 ® ® • Follow all applicable national and local codes for IR NECIEC PE IR NEC® Class 2 20 V ProgrammableCCIOccComCOM20 VNECIEC PEMan. OverrideOccCCIComCOMMUXMUXMUXMUX24 VCOMCOMIEC PELV Photo Photo +1.844.LUTRON1 HomeWorks Universal DALI Power Module Tc > 75 ºC Energi Savr Node QS +44.(0)20.7702.0657 proper circuit separation and protection. LQSE-2DALUNV-D Z096+91.124.4390130 Test | Prueba QSNE-2DAL-D N1771 lutron.com Tester 230 V~ 50/60 Hz 100 mA 50

www.lutron.com

220–240 V~ 50/60 Hz 80 mA 120 V~ 50/60 Hz 120 mA 243C IND.CONT.EQ. lutron.com/ +44.(0)20.7680.4481 ChinaRohs L N 60 ºC/75 ºC Cu Al 0,6 N•m (5.0 in-lb) 8,0 mm(5/16 in) • Wiring may be daisy chained or t-tapped. • Total length of QS link must not exceed 610 m (2000 ft). V D E QS Link Available from Wiring Length Wire Gauge Lutron in one cable: * Power (terminals 1 and 2): QS-CBL-LSZH 2 (Low-Smoke 1 pair 1.0 mm (18 AWG) Zero-Halogen) Less than GRX-CBL-346S 153 m (502 ft) Data (terminals 3 and 4): (non-plenum) 1 pair 0.5 mm2 (22 AWG), twisted and screened GRX-PCBL-346S (plenum) Power (terminals 1 and 2): GRX-CBL-46L 153 m to 1 pair 4.0 mm2 (12 AWG) (non-plenum) 610 m (502 ft Data (terminals 3 and 4): GRX-PCBL-46L to 2000 ft) 1 pair 0.5 mm2 (22 AWG), (plenum) twisted and screened * Varies by region, refer to the cable spec. 2 (1) COM • Use one, twisted-screened pair of 0.5 mm (20 AWG) Assembled in Mexico for data link (MUX, _). NEC® Class 2 DA 1 DA 2 NEC® Assemblé aux Mexique (2) N / C Ensamblado en México MUX MUX COM IEC PELV Class 2 (3) MUX HomeWorks QS (4) MUX Ta > 65 ºCLQSE-2DAL-D

Neither supplies nor consumes PDUs Test | Prueba120 V~ 50 / 60 Hz 120 mA 224433CC IINDND..CCOONNTT..EEQQ.. +1.844.LUTRON1 Tester230 V~ 50 / 60 Hz 80 mA +44.(0)20.7702.0657 lutron.com LNTa 65 °C 65/75 ºC Cu Al 5 in-lb (0,6 N•m) 5/16 in (8 mm) 7 ®SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:

Page 8

HomeWorks LQSE-2DALUNV-D DALI® Power Module 3691179c 8 08.11.22 Wiring: Contact Closure Inputs COM (10) Manual Override CCI Wiring (IEC PELV / NEC® Class 2) Man. Override CCI (9) • The attached device must provide a closed dry COM (5) contact closure or solid-state output. Programmable • Input is miswire-protected up to 36 V-. CCI (4) • The DALI® Power Module with DALI® is shipped with a jumper pre-installed in the Emergency Contact Closure Input. • Manual Override mode is activated by opening the Emergency Contact Closure. Pre-installed jumper must be removed to utilize this function. 1 2 3 4 5 6 7 8 9 10 • See the Emergency Lighting Systems Application Note (P/N 048106) at www.lutron.com for more details. 4 5 9 10 Programmable Wiring (IEC PELV / NEC® Class 2) 1 1 2 2 • The attached device must provide a dry contact V V QS Ethernet DALI 1 DALI 2 3 Class 2 L 3 4 Class 2 L 4 closure, solid-state output, open collector or active- DA 1 DA 2 ® ® low (NPN) / active-high (PNP) output. IR NEC IEC PE IR NEC® Class 2 ProgrammableCCI COM NEC IEC PE Man. OverrideCCI COM MUX MUX COM IEC PELV Occ Occ – Open collector NPN or active-low on-state voltage 20 V Photo Com 20 V Photo Com MUX MUX 24 V COM must be less than 1 V- and sink 3.0 mA +1.844.LUTRON1 HomeWorks Universal DALI Power Module Tc > 75 ºC Energi Savr Node QS +44.(0)20.7702.0657 – Output collector PNP or active-high on-state voltage LQSE-2DALUNV-D Z096+91.124.4390130 must be greater than 12 V- and source 3.0 mA Test | Prueba QSNE-2DAL-D N1771 lutron.com 4 5 9 10 1 1 2 2 230 V~ 50/60 Hz 100 mA V V QS Ethernet DALI 1 DALI 2 3 Class 2L 3 4 Class 2L 4 Tester DA 1 DA 2 – The outputs must stay in the closed or open ® ® 50 IR NECIEC PE IR NEC® Class 2 ProgrammableCCIOccCOM NECIEC PEMan. OverrideOccCCICOMMUX MUX COM IEC PELV www.lutron.com 20 V Photo Com 20 V Photo Com MUX MUX 24 V COM HomeWorks Universal DALI Power Module +1.844.LUTRON1 Tc > 75 ºC Energi Savr Node QS +44.(0)20.7702.0657 220–240 V~ 50/60 Hz 80 mA 243C IND.CONT.EQ. states for at least 40 msec in order to be LQSE-2DALUNV-D 120 V~ 50/60 Hz 120 mA lutron.com/ Test | Prueba QSNE-2DAL-D Z096+91.124.4390130 +44.(0)20.7680.4481 lutron.com N1771 ChinaRohs Tester 230 V~ 50/60 Hz 100 mA 50

www.lutron.com

220–240 V~ 50/60 Hz 80 mA 120 V~ 50/60 Hz 120 mA 243C IND.CONT.EQ. lutron.com/ +44.(0)20.7680.4481 ChinaRohs recognized by the DALI® Power Module L N 60 ºC/75 ºC Cu Al 0,6 N•m (5.0 in-lb) 8,0 mm(5/16 in) 60 ºC/75 ºC Cu Al 0,6 N•m (5.0 in-lb) 8,0 mm(5/16 in) L N • If there is any question as to whether the third-party device generating these outputs is compatible with V D E these specifications, contact the manufacturer. • Input is miswire-protected up to 36 V-. V D E The Lutron logo, Lutron, GRAFIK Eye, HomeWorks, and Sivoia are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries. All other product names, logos, and brands are property of their respective owners. 8 ®SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number: