Future Automation TSLH SONY FW85 example technical sheet

Page 1

ISSUE001 Technical Sheet TSL-H - Telescopic Screen Lift - SONY FW85 SHEET 1 OF 6 DESIGN HIGHLIGHTS FUNCTION UP • Quiet smooth fast action An electric mechanism to lift with variable speed motion a screen out of a cabinet. Custom made to suit screen • Full cable management size. It is designed to keep all the mechanism behind • Wide range of mounting the screen to save in cabinet options. height. • As height efficient as SUITABILITY possible. This TSL has been sized for a • Marine Suitable. SONY BRAVIA FW-85BZ35F screen. 1911 x 1098 x 73. OPTIONS Maximum weight for this DOWN mechanism is a screen of 60Kg • Outdoor Option. and an enclosure and lid weight of 40Kg. Absolute maximum. • Medium Duty version. CONTROL Supplied with basic infrared remote. Can be learnt by many learning remotes. Also has switch control and RS232 so can be operated by relays, switches, Crestron / AMX or Lutron systems. Mechanism as supplied. WARNING IMPORTANT Mechanisms which lift It is the responsibility of or move weights need the installer to warn all to be checked on a potential end users of yearly basis for any the dangers of interfering damage which may with mechanisms during result in an accident operation US www.futureautomation.net tel: +1 (603) 742 9181 UK www.futureautomation.co.uk tel: +44 (0) 1438 833 577

Page 2

ISSUE001 SHEET 2 OF 6 Technical Sheet TSL-H - Telescopic Screen Lift - SONY FW85 Key hole details allow the enclosure LID and ENCLOSURE - To be to be hooked into made by others. Total place. allowable weight for all timber DETAIL A work and lid is 40Kg. SCALE 1 : 8 The lid must be easily removed if the Brackets for mechanism was stuck in the down enclosure allow position. The fixings for the screen are adjustment. at the top here so it can then be lifted off. The drive to the motor can also be disconnected here allowing the screen and mechanism to be manually lifted. Screen cables enter here Lifting eyes can Screen added here to cables enter assist in manual here Lifting/recovery. A Access here to disconnect motor. Front access is required to install the lift. Allow 25mm in front of the screen if the mechanism is to be partially sunk below floor level. TRIM PANEL - Not supplied. This trim panel is lifted up as the screen is lowered into the cabinet. Brackets are supplied to attach it. US www.futureautomation.net tel: +1 (603) 742 9181 UK www.futureautomation.co.uk tel: +44 (0) 1438 833 577

Page 3

ISSUE001 SHEET 3 OF 6 Technical Sheet TSL-H - Telescopic Screen Lift - SONY FW85 DOWN C A DETAIL C SCALE 1 : 4 44.76 1137 B B 0.53 13.50 A

0 2.78 0.00 7.89 70.50 10.77 200.50 273.50 SECTION B-B SCALE 1 : 8 0.20 75.24 5 Screen Width 1911 1.54 39 10.77 273.50 0.00 0 2.78 70.50 SECTION A-A 0.00 SCALE 1 : 8 0 77.20 Box Size 1961 US www.futureautomation.net tel: +1 (603) 742 9181 SEE CAD FOR FINER DETAIL UK www.futureautomation.co.uk tel: +44 (0) 1438 833 577

Page 4

ISSUE001 SHEET 4 OF 6 Technical Sheet TSL-H - Telescopic Screen Lift - SONY FW85 DETAIL E 90.35 SCALE 1 : 2 UP D SECTION D-D 2295 SCALE 1 : 12 89.17 2265 0.28 Rebate in 7 Enclosure E 0.14 3.50 Enclosure Screen signal and power 0.53 cables enter cable tracks 13.50 here on both sides 0.47 0.53 Trim Panel 12 13.50 Thickness The lift cables exit the 45.94 Trim Panel mechanism here and have a 1167 3m flying lead to the control * * system. 44.76 0.79 1137 Enclosure 20 The control box is 320mm x Thickness 130mm x 230mm and requires a 220/240VAC supply. All control connections are made here. D 0.16 4 0.00 0 8.70 77.91 LID DEPTH 221 LID WIDTH 1979 The trim panel is attached to a 9.06 certain part of the mechanism so OPENING DEPTH 230 78.23 that it is lowered at a different rate to OPENING WIDTH 1987 the screen. US www.futureautomation.net tel: +1 (603) 742 9181 SEE CAD FOR FINER DETAIL UK www.futureautomation.co.uk tel: +44 (0) 1438 833 577

Page 5

ISSUE001 SHEET 5 OF 6 Technical Sheet TSL-H - Telescopic Screen Lift - SONY FW85 G LID Lid must lift off easily ENCLOSURE DESIGN Block or detail to locate lid 20-22mm [0.8 - 0.9] 43.62 1108 38.31 973 IMPORTANT The Enclosure, Lid and 28.46 Mount Plate the Trim panel must weigh 723 no more than 40Kg. F F TRIM PANEL Suggested Taper Edge 12-13mm [0.47-0.51] 15.08 10° 34.49 383 876 5.24 133 200 32.52 7.87 826 0.00 1.18 0 530 20.87 30 Trim 0 mounts 7.70 18.33 0.00 465.50 SECTION F-F 195.50 Block to locate lid. SCALE 1 : 12 DETAIL G SCALE 1 : 3 0 223 8.78 0.00 846 623 US www.futureautomation.net tel: +1 (603) 742 9181 SEE CAD FOR FINER DETAIL 33.31 24.53 UK www.futureautomation.co.uk tel: +44 (0) 1438 833 577

Page 6

ISSUE001 SHEET 6 OF 6 Technical Sheet TSL-H - Telescopic Screen Lift - SONY FW85 Remove Screen Upright Fixings INSTALL INSTRUCTIONS • Check that the cabinet, enclosure, lid and the trim panel are Remove Screen Upright Fixings made to the details shown on the previous pages. • You can stand the mechanism up on its base to test it before putting in the cabinet. See control document for Fix enclosure brackets to the details. Use the IR remote with caution and always cover enclosure at the positions the STOP button in case of issues. See control document. shown on the previous page. • Centrally fix the mechanism to the back of the cabinet in the places shown. • Run up and down and then add the enclosure. Trim Panel - • Adjust the position of the enclosure and adjust the up and fixing plates will down switches with caution. Temporarily add lid to check be supplied. height. • Run screen cables up into enclosure. Secure cables as they enter and leave the cable tracks with cable ties. Make sure no cables can get tangled or caught as the mechanism moves. • Add trim panel. And adjust so it does not clash in the up or down positions. Watch as it initially moves and cover the STOP button. • The uprights can be removed from the mechanism and Adjuster for up added to the screen at the correct height. Rest screen on switch. floor to connect cables before hooking into place. Fixings at top • Check movement with screen with caution. and bottom - • both sides. • Adjust switches with caution. Check in the control box to make sure the switches are acting correctly. CC2 LED for Adjuster for down up position and CC1 LED for down. They go off when hit. switch. US www.futureautomation.net tel: +1 (603) 742 9181 UK www.futureautomation.co.uk tel: +44 (0) 1438 833 577