Future Automation TSLH LG110 example technical sheet

Page 1

TSL-H - LG110 TELESCOPIC SCREEN LIFT HEAVY FUNCTION An electric mechanism to lift UP a screen out of a cabinet. Custom made to suit screen size. Internal cabinet height can be as little as screen height + 40mm [1.6"]. SUITABILITY This TSL has been sized for a DOWN LG110UM5J-B screen. Maximum weight for this mechanism is a screen weight of 80Kg [176lb] and an enclosure weight of 120Kg [264lb]. Absolute maximum. CONTROL Supplied with basic infrared remote. Can be learnt by many learning remotes. Also has switch control and RS232 so can be operated by relays, switches, Crestron / AMX or Lutron systems. Mechanism as WARNING IMPORTANT supplied. Mechanisms which lift It is the responsibility of or move weights need the installer to warn all to be checked on a potential end users of yearly basis for any the dangers of interfering damage which may with mechanisms during result in an accident operation TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 001 WWW NET . . SHEET 1 FUTUREAUTOMATION

Page 2

TSL-H - LG110 TELESCOPIC SCREEN LIFT HEAVY LID and ENCLOSURE - To be made by others. Total allowable A weight for all timber work and lid is 120Kg [264lb]. The lid must be easily removed if the mechanism was stuck in the down position. The fixings for the screen are at the top here so it can then be lifted off. The drive to the motor can also be disconnected here allowing the screen and mechanism to be manually lifted. Lifting eyes can added here to Screen assist in manual cables Lifting/recovery. enter here Screen cables Access here to enter here disconnect motor. Key hole details allow the enclosure DETAIL A to be hooked into place. Front access is required to install the lift. Allow 25mm [1"] in front of the screen if the Brackets for mechanism is to be partially sunk below floor enclosure allow level. adjustment. TRIM PANEL - Not supplied. This trim panel is lifted up as the screen is lowered into the cabinet. Brackets are supplied to TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 attach it. ISSUE 001 WWW NET . . SHEET 2 FUTUREAUTOMATION

Page 3

TSL-H - LG110 TELESCOPIC SCREEN LIFT HEAVY 3 7/8" 99.10 Screen DOWN Depth A C B B 55 7/16" 1408 DETAIL C Screen SCALE 1 : 4 Height 97 3/8" 2474 Screen Width

0 12" 70.50 305.50 2 3/4" 8 1/8" 206.40

1436 1418 56 9/16" 55 13/16" 13/16" A 20 Internal Cabinet Height Enclosure Internal Enclosure Height 3/16" Thickness 5 12" 305.50 9 1/4" 235 Enclosure 2 3/4" Depth 70.50 0 99 3/8" SECTION B-B SECTION A-A 13 3/4" 2524 SCALE 1 : 10 SCALE 1 : 10 350 Enclosure Width Internal Cabinet Depth 103 5/16" 2624 Internal Cabinet Width TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 001 WWW NET . . SHEET 3 FUTUREAUTOMATION SEE CAD FOR FINER DETAIL

Page 4

TSL-H - LG110 TELESCOPIC SCREEN LIFT HEAVY D UP DETAIL E SCALE 1 : 3 13/16" 20 Enclosure Thickness Enclosure 56 5/8" 1/4" 1438 7 Rebate in Enclosure E 1/2" 12 Trim Panel Thickness 1/8" Trim Panel 3.50 Screen signal and power cables enter cable tracks here on both sides The trim panel is attached to a certain part of the mechanism so that it is lowered at a different rate to the screen. The lift cables exit the mechanism here and have a 3m flying lead to the control system. 9 13/16" 250 Lid Depth 3/16" D 5 10 1/4" 100" 260 2540 Opening Depth Lid Width 100 3/8" SECTION D-D 2550 SCALE 1 : 12 Opening Width TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 001 WWW NET . . SHEET 4 FUTUREAUTOMATION SEE CAD FOR FINER DETAILS

Page 5

TSL-H - LG110 TELESCOPIC SCREEN LIFT HEAVY Lid must lift off easily LID G Block or detail 13/16" to locate lid ENCLOSURE DESIGN 20 99 3/8" 2524 55 13/16" 1418 IMPORTANT 50 1/2" Mount Plate The Enclosure, Lid and the 1283 Trim panel must weigh no more than 120Kg [264lb]. 40 11/16" 1033 34 1/2" 876 F F 12-13mm [0.47-0.51] TRIM PANEL 22 15/16" Suggested 583 Taper Edge 10° 13 1/8" 333 Trim mounts 32 1/2" 826

0 225

8 7/8" 1 3/16"

30 Block to locate lid. 427 645 849 697 25 3/8" 16 13/16" 33 7/16" 27 7/16"

DETAIL G 0

SCALE 1 : 4 SECTION F-F

0 193 7 5/8" 846 TECHNICAL SHEET 653

33 5/16" UK +44 (0) 1438 833577 US +1 (603) 742 9181 SEE CAD FOR FINER DETAIL ISSUE 001 25 11/16"

WWW NET . . SHEET 5 FUTUREAUTOMATION

Page 6

TSL-H - LG110 TELESCOPIC SCREEN LIFT HEAVY INSTALL INSTRUCTIONS Remove Screen Upright Fixings • Check that the cabinet, enclosure, lid and the trim panel are made to the details shown on the previous pages. Remove Screen Upright Fixings • You can stand the mechanism up on its base to test it before putting in the cabinet. See control document for details. Use the IR remote with caution and always cover the STOP button in case of issues. Fix enclosure brackets to the • Centrally fix the mechanism to the back of the cabinet in enclosure at the positions the places shown. shown on the previous page. • Run up and down and then add the enclosure. • Adjust the position of the enclosure and adjust the up and down switches with caution. Temporarily add lid to check height. Trim Panel - fixing • Run screen cables up into enclosure. Secure cables as plates will be supplied. they enter and leave the cable tracks with cable ties. Make sure no cables can get tangled or caught as the mechanism moves. • Add trim panel. And adjust so it does not clash in the up or down positions. Watch as it initially moves and cover the STOP button. • The uprights can be removed from the mechanism and added to the screen at the correct height. Rest screen on floor to connect cables before hooking into place. • Check movement with screen with caution. Fixings at top and bottom - both sides. TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 001 WWW NET . . SHEET 6 FUTUREAUTOMATION