This document could not be shown here. Open the PDF.
Text of this document6 pages · 3,541 words
Page 1
QS DMX Control Interface English Installation and Operation Instructions QSE-CI-DMX Occupant Copy Please Read PELV (Class 2: USA) Device 24 V 60 mA The QSE-CI-DMX control interface allows zones on a Requirements GRAFIK Eye® QS Wireless to control DMX512-controlled devices. Any zone on the GRAFIK Eye QS Wireless can The QSE-CI-DMX requires the following: Español be mapped to either a single DMX512 channel or to three • At least one GRAFIK Eye QS Wireless control unit wired separate DMX512 channels, for RGB/CMY color-control to the QSE-CI-DMX through the QS communication link applications. • A QS Link Power Supply, such as the QSPS-P1-1-50, is required if the GRAFIK Eye QS Wireless is powering any Key Features other QS link devices drawing a total of two (2) or more • Map any zone on a GRAFIK Eye QS Wireless control unit power draw units to any single DMX512 channel • DMX512 link terminators at both ends of the DMX512 link Français • Map any zone on a GRAFIK Eye QS Wireless control unit (available from Lutron, part number LT-1) simultaneously to three DMX512 channels for RGB/CMY • QS Communication Link Wire (PELV, Class 2: USA) 2 color-control - Two 18 AWG (1.0 mm ) conductors for control power 2 • Integral RGB/CMY color lookup table that maps GRAFIK - One twisted, shielded pair of 22 AWG (1.0 mm ) for Eye QS zone intensities to RGB/CMY values data link • RGB/CMY table can be customized by using the Lutron - Available from Lutron, part number GRX-CBL-346S; QS Color Configuration Tool (PC application available on check compatibility in your area the CD packaged with the QSE-CI-DMX, and on www. Mounting lutron.com/qs) Choose a mounting method below. Mount the control QS System interface in an accessible location. Lutron QS System components communicate over A. WallMounting.Mount the control interface directly on a the highly flexible QS link. There are a few rules to wall, as shown in the Mounting Diagram, using screws keep in mind when designing and installing QS system (not included). When mounting, provide sufficient space components: for connecting cables. • Up to 100 devices on one QS link B. RackMounting.Place the interface in the LUT-19AV-1U • Up to 100 zones on one QS link AV rack using the screws provided with the interface. • Up to 2000 ft (610 m) wiring length The LUT-19AV-1U will hold up to four units. • Only one QSE-CI-DMX per QS link C. ConduitMounting.If conduit is desired for wiring, the - Counts as one (1) device LUT-5x10-ENC can be used to mount one unit. - Counts as zero (0) zones • Contact Lutron for compatibility with Quantum® Dimensions 2.50 in (63.5 mm) Mounting Holes Mounting Options Terminal blocks on this side 3.75 in 4.26 in Wall (95.3 mm) (108.2 mm) 2.50 Control Interface 3.75 4.26 5.26 in LEDs and (133.6 mm) addressing 5.26 switches on this side LUT-19AV-1U LUT-5x10-ENC 1.06 in (26.9 mm) 1.06 ®
Page 2
Control Interface Wiring PowerOptions • The QSE-CI-DMX draws two (2) power draw units. A • Another option is to power the QSE-CI-DMX from a QS GRAFIK Eye® QS Wireless is capable of supplying up to Link power supply (QSPS-P1-1-50, QSPS-P2-1-50, three (3) power draw units, and can be used to supply or QSPS-P3-1-50) or a QS shade panel power supply power to the QSE-CI-DMX if the GRAFIK Eye QS Wireless (QSPS-P2-10-60 for 230 V , or QSPS-P1-10-60 for is not powering any other QS link devices drawing a total 120 V ). Please see www.lutron.com/qs for details. of two (2) or more power draw units. PoweredbyGRAFIKEye®QSControlUnit • Each PELV (Class 2: USA) terminal accepts up to two • Common (terminal 1) and 24 V (terminal 2): 2 2 18 AWG (1.0 mm ) wires. Two 18 AWG (1.0 mm ) conductors. Ensure that • Connect the terminal 1, 3, and 4 connections to all control the terminal 2 connection is wired correctly. Refer to units, wallstations, and control interfaces. See Power GRAFIK Eye QS Specification Submittal for more details. Options for pin 2 connectivity. • Data link (terminals 3 and 4): One shielded, twisted pair 2 • Total length of control link must not exceed 2000 ft. 22 AWG (1.0 mm ). (610 m). • Do not allow PELV (Class 2: USA) wires to contact line/ mains wires. DMX Link QS Link Do not connect terminal 2 if using external power supply 4 3 2 1 4 3 2 1 1 2 Lutron Cable A B C GRX-CBL-346S-500 1 2 3 4 1 2 3 4 5 6 L N QS Link: 1: Common Rear View of GRAFIK Eye QS Control Unit 2: Power 3: MUX Wire Strip Length 4: MUX 3/8 in 3/8 in. m(m1)0 ControlInterfaceWiring:PoweredSeparately (10 mm) Data Link - (1) twisted, shielded pair 2 22 AWG (1.0 mm ) 3: MUX 4: MUX D: Drain/Shield QSE-CI-DMX (2) 12 AWG 2 (2.5 mm ) (1) 18 AWG 2 (1.0 mm ) (1) 18 AWG 2 PELV (Class 2: USA) (1.0 mm ) To DMX equipment Control wiring 1: Common 2: 24 V (2) 12 AWG 2 (2.5 mm ) 2 QSE-CI-DMX Control Interface Installation and Operation Instructions ®
Page 3
DMX-512 Link Wiring Connect the DMX link terminals on the QSE-CI-DMX interface to input terminals on DMX512-controlled equipment. 2 • Each terminal on the QSE-CI-DMX accepts two 18 AWG (1.0 mm ) wires. • Link must be 1000 feet (305 m) or less. • Link must begin and end with link terminators (available from Lutron; part number LT-1). Pin on QSE-CI-DMX Terminal Connection to DMX Equipment 1: DMX512 system COMMON Pin 1 Note: Do NOT connect to COMMON on GRAFIK Eye QS control unit or processor NC Not connected 3: DMX512 system DATA + Pin 3 on DMX equipment 2: DMX512 system DATA - Pin 2 on DMX equipment Functionality of LEDs and Configuration Switches Program button 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 QSE-CI-DMX Configuration Switches LED 1: Power 1: Unused LED 2: Unused 2: Up = 44 packets per second LED 3: Status (DMX refreshes 44 times per second) LED 4: DMX Link Tx Down = 22 packets per second LED 5: DMX Link Rx (DMX refreshes 22 times per second; LED 6: QS Link Tx for older/slower DMX devices) LED 7: QS Link Rx 3: Unused 4: Unused 5: Unused 6: Up = Override to 0 intensity on all DMX channels Down = Normal operation 7: Up = Override to Minimum levels on all DMX channels Down = Normal operation 8: Up = Override to Maximum levels on all DMX channels Down = Normal operation Switch Logic Switch up Switch down ® QSE-CI-DMX Control Interface Installation and Operation Instructions 3
Page 4
Programming Assigning a Single DMX Channel to a If the selected channel is already assigned to a zone, the GRAFIK Eye® QS Zone GRAFIK Eye QS will prompt you to confirm replacing the Most DMX fixtures use single-channel assignment. If you channel with the new selection. Press OK to confirm the are using single-channel DMX, follow the instructions replacement, or cancel to go back. below. If your DMX fixture has 3 channels (RGB or 5. Repeat step 4 for each DMX zone. CMY), refer to the instructions at right for 3-channel DMX 6. Exit programming mode: Press and hold the programming assignment. button on the QSE-CI-DMX for 3 seconds. The yellow Zone 4 1. Enter programming mode on the status LED will blink once per second. GRAFIK Eye QS. Choose “Zone Assigning RGB/CMY DMX Channels (3-Channel DMX) DMX Setup” then “Load Type” from the to GRAFIK Eye® QS Zones Main Menu. For the zones you wish to assign to DMX channels, change Zone 4 1. Enter programming mode on the the load type to DMX. GRAFIK Eye QS. Choose “Zone 2. Exit programming mode on the GRAFIK Eye QS. Setup” then “Load Type” from the 3. Enter programming mode on the QSE-CI-DMX: Press RGB/CMY DMX Main Menu. For the zones you wish and hold the programming button for 3 seconds. The to assign to RGB/CMY channels, yellow status LED will blink rapidly. change the load type to RGB/CMY DMX Prog On any GRAFIK Eye control units on DMX. the link, the zone LEDs will indicate 2. Exit programming mode on the GRAFIK Eye QS. Press zone R&L their status: LEDs of assigned zones 3. Enter programming mode on the QSE-CI-DMX: Press and buttons to will go to full on (all LEDs lit) then hold the programming button for 3 seconds. The yellow Toggle assignment flash, and all LEDs of unassigned status LED will blink rapidly. zones will go to Off. To toggle Zone 4- RGB/CMY On any GRAFIK Eye control units on assignment, press the zone raise and Component 1 channel the link, the zone LEDs will indicate lower buttons together. their status: LEDs of assigned zones Zone 4 4. The GRAFIK Eye QS will display the 14 will go to full on (all LEDs lit), and LEDs Choose Channel on selected zone and an unassigned of unassigned zones will go to full off DMX AABB-CCEE DMX channel. Use the master (all LEDs off). To toggle assignment, 14 buttons on the GRAFIK Eye QS to press the zone raise and lower buttons choose a DMX channel (from 1 to together. 512) for this zone. 4. The GRAFIK Eye QS will display the selected zone and an unassigned DMX channel. Use the master buttons on the GRAFIK Eye QS control unit GRAFIK Eye QS to choose a DMX component channel Zone LEDs (from 1 to 512) for this zone. Press the Scene 1 button on 1 9 2 10 3 11 4 12 5 13 6 14 7 15 8 16 the GRAFIK Eye QS to cause the currently selected DMX Zone LEDs full on and flash channel to flash. Press OK to assign the selected DMX 9-16 (zone assigned to 1-8 OK channel to the selected zone and proceed. Repeat for all QSE-CI-DMX) 3 channels. Press cancel to go back. Zone LEDs Off If the selected channel is already assigned to a zone, the (zone unassigned to GRAFIK Eye QS will prompt you to confirm replacing the QSE-CI-DMX) channel with the new selection. Press OK to confirm the Press the Zone raise replacement, or cancel to go back. and Zone lower buttons 5. Repeat step 4 for all the RGB DMX zones. simultaneously to assign a 6. Exit programming mode: Press and hold the programming DMX channel button on the QSE-CI-DMX for 3 seconds. The yellow Press cancel to go status LED will blink once per second. 1 92 103 114 125 136 147 158 16 back to step 4. Press Master buttons the Scene 1 button on the GRAFIK Eye QS 9-16 1-8 OK to cause the currently OK button selected DMX channel Cancel to flash. Press OK to Scene 1 button assign the selected DMX channel to the selected zone and proceed. Note: Do not use the Flash feature with DMX devices containing moving parts (shade motors, motorized light fixtures, smoke-oroducing machines, etc.). to avoid damaging those devices or causing unexpected motion. 4 QSE-CI-DMX Control Interface Installation and Operation Instructions ®
Page 5
To unassign DMX channels from a GRAFIK Eye QS: To enable/disable Master Raise/Lower from 1. Enter programming mode on the QSE-CI-DMX: Press and affecting RGB/CMY zones (disabled by hold the programming button for 3 seconds. The yellow default) status LED will blink rapidly. 1. After assigning RGB/CMY zones to the GRAFIK Eye QS, 2. The LEDs of the zones assigned to DMX channels will be enter programming mode on the GRAFIK Eye QS and flashing full on. To toggle assignment, press the desired choose “Zone Setup” from the Main Menu. Select “RGB/ zone’s raise and lower buttons together. CMY config”. Zone 4 3. Press “OK” to confirm, or “Cancel” to 2. Use the Master Button to choose “Enabled” or “Disabled”. Channels 1,2,3 cancel the operation. Press “OK” to save. on DMX AABB-CCDD 4. Exit programming mode: Press and 3. Exit programming mode. Unassign? hold the programming button on the QSE-CI-DMX for 3 seconds. The yellow status LED will blink once per second. Color Programming Tool Note: The RGB/CMY table can be The QSE-CI-DMX comes with a standard table of colors edited to map a zone intensity to a already loaded. Users can modify the table to achieve specific RGB/CMY color using the desired colors. color configuration tool for the QSE-CI- 1. Install the program from the CD. DMX (available at www.lutron.com/qs). 2. Create a new project, or use the provided default color Display Type Setup table. 3. If you are creating a new project, you can enter individual There are two display types to choose from: “% display”, color values in either RGB (red-green-blue) or CMY (cyan- which displays light intensity as a percentage, and “0-255 magenta-yellow) format. Values can be entered in either display”, which displays intensity as a numeric value. For decimal or hexadecimal format. Additionally, the interpolate RGB DMX zones, it may be desirable to select “0-255 function will fill in values automatically when you define the display” in order to step through each entry in the RGB/ boundary values. CMY table. This option is available only after DMX channel 4. Use the “Test” feature on the title bar to view your edited assignment. color table. Display type 1. Enter programming mode on the 5. Connect a mini-USB cable between 1 9 2 10 3 11 4 12 5 13 6 14 7 15 8 16 your PC and the mini-USB port GRAFIK Eye QS, and choose “Zone under the bottom hinged door of Set zones 9-16 Setup” from the Main Menu. Select 1-8 OK your GRAFIK Eye QS Wireless. “Display type”. The LEDs of the zones 6. Use the “Transfer” command to assigned to DMX channels will be either download your color table into flashing full on. the QSE-CI-DMX, or to extract a 2. Use the zone raise/lower buttons to color table from a QSE-CI-DMX to toggle between display types. Press Mini-USB port your PC for further editing. “OK” to confirm. Repeat for all desired zones. 3. Exit programming mode. Trim Setup The high end and low end trim settings of a zone assigned to a DMX channel can be manually set as desired, but only for zones assigned to DMX channels. High and low end trim settings limit the maximum and minimum output of a dimming zone. Trim levels are set automatically when the load type is programmed. Remote high end 1. Enter programming mode on the GRAFIK Eye QS, and choose “Zone Set zones Setup” from the Main Menu. Select “Remote high end” or “Remote low end”. The LEDs of the zones assigned to DMX channels will show the high end or low end intensity. 2. Use the zone raise/lower buttons to set the desired trim levels. Repeat for all desired zones and trims. Press “OK” to confirm. 3. Exit programming mode. ® QSE-CI-DMX Control Interface Installation and Operation Instructions 5
Page 6
Lutron Electronics Co., Inc. Internet: www.lutron.com One Year Limited Warranty E-mail: product@lutron.com For a period of one year from the date of purchase, and subject to the exclusions and restrictions described below, Lutron warrants each new unit to be free from manufacturing defects. Lutron will, at its option, either repair the defective unit or issue a credit equal to the World Headquarters purchase price of the defective unit to the Customer against the purchase price of comparable replacement part purchased from Lutron. USA Replacements for the unit provided by Lutron or, at its sole discretion, an approved vendor may be new, used, repaired, reconditioned, LutronElectronicsCo.,Inc. and/or made by a different manufacturer. 7200SuterRoad, If the unit is commissioned by Lutron or a Lutron approved third party as part of a Lutron commissioned lighting control system, the term Coopersburg,PA18036-1299 of this warranty will be extended, and any credits against the cost of replacement parts will be prorated, in accordance with the warranty TEL+1.610.282.3800 issued with the commissioned system, except that the term of the unit’s warranty term will be measured from the date of its commissioning. FAX+1.610.282.1243 EXCLUSIONS AND RESTRICTIONS Toll-Free1.888.LUTRON1 This Warranty does not cover, and Lutron and its suppliers are not responsible for: TechnicalSupport 1. Damage, malfunction or inoperability diagnosed by Lutron or a Lutron approved third party as caused by normal wear and tear, abuse, 1.800.523.9466 misuse, incorrect installation, neglect, accident, interference or environmental factors, such as (a) use of incorrect line voltages, fuses or circuit breakers; (b) failure to install, maintain and operate the unit pursuant to the operating instructions provided by Lutron and the North and South America applicable provisions of the National Electrical Code and of the Safety Standards of Underwriter’s Laboratories; (c) use of incompatible Technical Hotlines devices or accessories; (d) improper or insufficient ventilation; (e) unauthorized repairs or adjustments; (f) vandalism; or (g) an act of God, USA,Canada,Caribbean: such as fire, lightning, flooding, tornado, earthquake, hurricane or other problems beyond Lutron’s control. 1.800.523.9466 2. On-site labor costs to diagnose issues with, and to remove, repair, replace, adjust, reinstall and/or reprogram the unit or any of its Mexico:+1.888.235.2910 components. Central/SouthAmerica: 3. Equipment and parts external to the unit, including those sold or supplied by Lutron (which may be covered by a separate warranty). +1.610.282.6701 4. The cost of repairing or replacing other property that is damaged when the unit does not work properly, even if the damage was caused by the unit. European Headquarters EXCEPT AS EXPRESSLY PROVIDED IN THIS WARRANTY, THERE ARE NO EXPRESS OR IMPLIED WARRANTIES OF ANY TYPE, United Kingdom INCLUDING ANY IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY. LUTRON DOES NOT LutronEALtd. WARRANT THAT THE UNIT WILL OPERATE WITHOUT INTERRUPTION OR BE ERROR FREE. 6SovereignClose,London, NO LUTRON AGENT, EMPLOYEE OR REPRESENTATIVE HAS ANY AUTHORITY TO BIND LUTRON TO ANY AFFIRMATION, E1W3JFUnitedKingdom REPRESENTATION OR WARRANTY CONCERNING THE UNIT. UNLESS AN AFFIRMATION, REPRESENTATION OR WARRANTY MADE TEL+44.(0)20.7702.0657 BY AN AGENT, EMPLOYEE OR REPRESENTATIVE IS SPECIFICALLY INCLUDED HEREIN, OR IN STANDARD PRINTED MATERIALS FAX+44.(0)20.7480.6899 PROVIDED BY LUTRON, IT DOES NOT FORM A PART OF THE BASIS OF ANY BARGAIN BETWEEN LUTRON AND CUSTOMER AND FREEPHONE(UK) WILL NOT IN ANY WAY BE ENFORCEABLE BY CUSTOMER. 0800.282.107 IN NO EVENT WILL LUTRON OR ANY OTHER PARTY BE LIABLE FOR EXEMPLARY, CONSEQUENTIAL, INCIDENTAL OR SPECIAL Technicalsupport DAMAGES (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF PROFITS, CONFIDENTIAL OR OTHER INFORMATION, +44.(0)20.7680.4481 OR PRIVACY; BUSINESS INTERRUPTION; PERSONAL INJURY; FAILURE TO MEET ANY DUTY, INCLUDING OF GOOD FAITH OR OF REASONABLE CARE; NEGLIGENCE, OR ANY OTHER PECUNIARY OR OTHER LOSS WHATSOEVER), NOR FOR ANY REPAIR WORK UNDERTAKEN WITHOUT LUTRON’S WRITTEN CONSENT ARISING OUT OF OR IN ANY WAY RELATED TO THE INSTALLATION, Asian Headquarters DEINSTALLATION, USE OF OR INABILITY TO USE THE UNIT OR OTHERWISE UNDER OR IN CONNECTION WITH ANY PROVISION OF Singapore THIS WARRANTY, OR ANY AGREEMENT INCORPORATING THIS WARRANTY, EVEN IN THE EVENT OF THE FAULT, TORT (INCLUDING LutronGLLtd. NEGLIGENCE), STRICT LIABILITY, BREACH OF CONTRACT OR BREACH OF WARRANTY OF LUTRON OR ANY SUPPLIER, AND EVEN IF 15HoeChiangRoad,#07-03 LUTRON OR ANY OTHER PARTY WAS ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EuroAsiaCentre,Singapore NOTWITHSTANDING ANY DAMAGES THAT CUSTOMER MIGHT INCUR FOR ANY REASON WHATSOEVER (INCLUDING, WITHOUT 089316 LIMITATION, ALL DIRECT DAMAGES AND ALL DAMAGES LISTED ABOVE), THE ENTIRE LIABILITY OF LUTRON AND OF ALL OTHER TEL+65.6220.4666 PARTIES UNDER THIS WARRANTY On ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, FAX+65.6220.4333 SALE, INSTALLATION, DELIVERY, USE, REPAIR, OR REPLACEMENT OF THE UNIT, OR ANY AGREEMENT INCORPORATING THIS WARRANTY, AND CUSTOMER’S SOLE REMEDY FOR THE FOREGOING, WILL BE LIMITED TO THE AMOUNT PAID TO LUTRON BY AsiaTechnicalHotlines CUSTOMER FOR THE UNIT. THE FOREGOING LIMITATIONS, EXCLUSIONS AND DISCLAIMERS WILL APPLY TO THE MAXIMUM NorthernChina: EXTENT ALLOWED BY APPLICABLE LAW, EVEN IF ANY REMEDY FAILS ITS ESSENTIAL PURPOSE. 10.800.712.1536 TO MAKE A WARRANTY CLAIM SouthernChina: To make a warranty claim, promptly notify Lutron within the warranty period described above by calling the Lutron Technical Support 10.800.120.1536 Center at (800) 523-9466. Lutron, in its sole discretion, will determine what action, if any, is required under this warranty. To better HongKong:800.901.849 enable Lutron to address a warranty claim, have the unit’s serial and model numbers available when making the call. If Lutron, in its sole Indonesia:001.803.011.3994 discretion, determines that an on-site visit or other remedial action is necessary, Lutron may send a Lutron Services Co. representative or Japan:+81.3.5575.8411 coordinate the dispatch of a representative from a Lutron approved vendor to Customer’s site, and/or coordinate a warranty service call Macau:0800.401 between Customer and a Lutron approved vendor. Singapore:800.120.4491 This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow Taiwan:00.801.137.737 limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some states do not allow the exclusion or Thailand:001.800.120.665853 limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Othercountries: Lutron, the sunburst logo, GRAFIK Eye, and seeTouch are registered trademarks of Lutron Electronics Co., Inc. +65.6220.4666 © 2009 Lutron Electronics Co., Inc. Lutron Electronics Co., Inc. ® Made and printed in U.S.A. P/N 040-248 Rev. A 07/22/09
Need assistance or looking to source this item?