This document could not be shown here. Open the PDF.
Text of this document26 pages · 1,974 words
Page 1
Instruction Manual WSR-DLI 15-Channel Digital Lighting Interface 2024 Version 2.1.0
Page 2
For programming information, see the Wired System Programming Guide For further installation information, see the Wired RAK Application Sheet Contents 1WhatistheWSR-DLI? 2Connections 3Installing the WSR-DLI 4Terminating the WSR-DLI 5AddingtheWSR-DLIasadevice 6ConfiguringtheWSR-DLI 6.1 Assigning Short Addresses 6.2 Force Readdress 6.3 Automatically Readdress 7ManagingtheWSR-DLIChannels 7.1 Grouped Mapping 7.2 Direct Mapping 7.3 Overriding a DLI Ballast 7.4 Store Auto Heal Data 8Ballast Configuration 8.1 Selecting ballasts 9Ballast Options 9.1 Fade Time 9.2 Fade Rate 9.3 Minimum Level 9.4 Maximum Leve 9.5 Power On Level 9.6 System Failure Level 9.7 Read Values 10Linear and Exponential Dimming (DT6) 11Colour Control (DT8) In Device Editor 11.1 Setting Colour Temperature 11.2 RGBWAFColour 12Colour Control (DT8) In Device Editor 12.1 Setting an RGB Scene in Rasoft Pro 12.2 Setting a Temperature Scene in Rasoft Pro 13Setting Colour and Temperature in the Rako App 13.1 Setting a Colour Scene in the Rako App 13.2 Setting Colour Tunable Scenes in the Rako App 14Advancedfeatures of WSR-DLI 14.1 Swap Channels 14.2 Visible Channels Appendix 1 - Hardware Changes Appendix 2 - Recommended Wiring Topology WSR-DLI Manual Version 2.1.0
Page 3
1WhatistheWSR-DLI? TheWSR-DLIisusedinaRakoWirednetworktointerfacewithupto64DLIBallasts, 15 groups can be created in a single Room. WhenusedwithcompatibleDT8Ballasts, the WSR-DLI can be used for RGBW and colour-tunable control. 2Connections TheWSR-DLIhastwowaysofconnectingtothe Rako Wired network, via the Daughterboard using a CAT5/CAT6, or via the RJ11 port using an RJ11 cable. TheRJ11connection can connect directly to a RAK-LINK, or wired accessories such as the WK-CONNECT,WK-CONNECTandWP-CON. TheDLIcontrol input is used to connect the DLI control cables which run to the DLI Ballasts. TheWSR-DLIcomeswitha12VDCpowersupply, this must be connected to the 12V DC port for the WSR-DLI to function. 3Installing the WSR-DLI POWERSHOULDBEISOLATEDTHROUGHOUTTHEINSTALLATIONPROCESS STEP1 Fix the back section of the WSR-DLI to the wall using the fixing points. NB Ensure there is a mains plug socket within 0.5M of the unit for the WSR-DLIpowersupply. WSR-DLI Manual Version 2.1.0
Page 4
STEP2 Connect the power supply which is supplied with the WSR-DLI. STEP3 Connect the DLI control cable which runs to the DLI Ballasts. WSR-DLI Manual Version 2.1.0
Page 5
STEP4 Connect to the Rako Wired Network via the RJ11 port or the Daughterboard. If the Daughterboard is used, it is essential to set the correct termination jumpers, see Terminating the WSR-DLI for more information. NB LEDswill illuminate on the WSR-DLI when a connection is made to the Rako Wired network, the DLI section of the WSR-DLI still requires permanent power from the 12V DC PSU. 4Terminating the WSR-DLI TERMINATIONONTHEWSR-DLIISONLYREQUIREDWHENUSINGTHE8-WAYKRONE CONNECTOR“CANCONNECT”DAUGHTERBOARD. Dependingontheposition of the WSR-DLI in the Rako Wired network, the termination required will be one of the following: NoTerm:BothJumpersremoved UsedwhentheWSR-DLIisnotattheendofline.Thisisusually identifiable by two cables being puncheddowntotheWSR-DLI. Term: Jumper fitted across 1+2 and 4+5 UsedwhentheWSR-DLIisendoflineinadaisychainconfiguration. Star Term: Jumper fitted across 2+3 and 5+6 UsedwhentheWSR-DLIisendoflineinaSTARwireconfiguration. WSR-DLI Manual Version 2.1.0
Page 6
5AddingtheWSR-DLIasadevice Before the WSR-DLI can assign DLI Ballasts, it needs to be added as a Device in Rasoft Pro. Wired System Programming Guide Thefollowing steps assume: - AProject File has been created. - Roomshavebeencreated. - TheHUBhasbeenconfigured. - TheChannels in the Rooms have been labelled. If the above has not been done, refer to the Wired System Programming Guide before continuing. - Select “File” - “New device” to bring up the “New device Wizard” - Select “WSR-DLI” and then select “Next”. WSR-DLI Manual Version 2.1.0
Page 7
- Choose the WSR-DLI name, and select “Next”. - Associate the WSR-DLI with a Room using the drop-down menu, leave “Associate to Channel” as it is and select “Next” WSR-DLI Manual Version 2.1.0
Page 8
- Put the WSR-DLI into Setup Mode by pressing and holding the blue setup button on the unit for 3-4 seconds. - OncetheWSR-DLIhasenteredSetupMode,theblueLEDontheunitwillblink periodically and the Device Setup Wizard will show ‘Device Found’. - Select “Finish”. WSR-DLI Manual Version 2.1.0
Page 9
- TheWSR-DLIhasbeenassignedinRasoftPro,it can be accessed by selecting it in the “Device List” 6ConfiguringtheWSR-DLI NowthattheWSR-DLIhasbeenaddedasaDevice,itrequiresfurthersetuptoassign DLI Ballasts to give them short addresses and group DLI Ballasts together should it be required. 6.1 Assigning Short Addresses Each DLI Ballast requires a unique short address so that it can be communicated with individually, multiple short addresses can be grouped within 15 Channels of the Rako Room to which the WSR-DLIis assigned. There are two options for assigning short addresses. WSR-DLI Manual Version 2.1.0
Page 10
6.2 Force Re-address Anyshort addresses on DLI Ballasts are replaced with new short addresses, this is typically used onnewsystems. 6.3 Automatically Re-address Will only assign short addresses to DLI Ballasts that do not have one, this is used on existing systems when additional DLI Ballasts have been added and the preservation of the short addresses on existing Ballasts is required. - Select the WSR-DLI in the “Device List” to open the “Device Editor”. - Select the “DLI Setup” tab. - Select “Force Re-address” which will assign short addresses to all connected DLI Ballasts. NB If DLI Ballasts have been added to an existing DLI network, select ‘Automatically Re-Address’ which will only assign short addresses to DLI Ballasts with no short address. - Theconnectedlights for the DLI Ballasts will flash when a short address has been assigned, once all DLI Ballasts have been given a short address, a window will appear saying how many Ballasts have been assigned, this should match the number of Ballasts which are connected to the WSR-DLI. WSR-DLI Manual Version 2.1.0
Page 11
7ManagingtheWSR-DLIChannels Theshort addresses on the DLI Ballasts need to be paired with Rako Channels, there are two options for grouping. 7.1 Grouped Mapping Multiple DLI short addresses can be grouped together onto a single Rako Channel, there can be up to 15 groups in a single Rako room across 64 DLI Ballasts. 7.2 Direct Mapping TheDLIshort address will relate directly to the Rako Channels, for example: DLI short address 0 would map to Rako Channel 1, DLI short address 1 would map to Rako Channel 2. 7.3 Overriding a DLI Ballast TheDLIBallast with an assigned short address can be tested by selecting a DLI Ballast with an assigned short address and pressing the following keys: The<,key=Sendoncommand The>.key=Sendoffcommand The?/key= Toggleon/off 7.4 Store Auto Heal Data After commissioning all DLI Ballasts, store the DLI network information, failing to do this will require re-commissioning all DLI Ballasts should any need to be replaced. WhenaDLIBallastis replaced and Auto Heal Data has been done, the new DLI Ballast will have its short address automatically uploaded when it is connected to the DLI bus. Should more than one DLI Ballast need to be replaced at the same time, the network should be re-addressed using Force Readdress. WSR-DLI Manual Version 2.1.0
Page 12
8Ballast Configuration Additional configuration is available via the Ballast Configuration menu once the DLI Ballasts have beenassigned short addresses. 8.1 Selecting ballasts Before any of the settings below can be set on the DLI Ballasts, the short address of the DLI Ballast must be selected, if the settings apply to all DLI Ballasts, then select “Broadcast (all ballasts)” Configurations will apply to all ballasts Configurations will apply to Ballast assigned short address 0 9Ballast Options 9.1 Fade Time Set how long it takes the light to reach full brightness from off, 3 seconds is recommended. WSR-DLI Manual Version 2.1.0
Page 13
9.2 Fade Rate Thespeedofdimmingwhenusingthe‘FadeUp’or ‘FadeDown’controls. 9.3 Minimum Level Thelowest level the light can reach, setting the minimum level >0 will result in the light not switching off. 9.4 Maximum Level Thebrightest level the light can reach, setting the maximum level to <0 will result in the light not switching on. 9.5 Power On Level Thedefault light level when power is restored to the system. 9.6 System Failure Level If the DLI signal is lost, the light level will default to this setting. 9.7 Read Values Reads the current configuration of the selected ballast. 10Linear and Exponential Dimming (DT6) For DT6 DLI ballast, there are two options for dimming, Linear and Exponential. 10.1 Linear Dimming (Recommended) Equally divides 0-255 levels across 0-100%. WSR-DLI Manual Version 2.1.0
Page 14
10.2 Exponential Dimming Within the lower dimming range, the driver's influence on light output evolves gradually, within the higher dimming signal range, its impact on lighting effects shifts more rapidly. 11Colour Control (DT8) In Device Editor DT8drivers can be configured to set colour temperature as well as RGBW. 11.1 Setting Colour Temperature To set the colour temperature of a ballast, first ensure that the ‘Colour Temperature’ box is ticked. - Fromthedrop-downmenu,selecttheScenetowhichthecolourtemperaturewill apply. - Using the sliders, select the intensity, and the desired temperature. WSR-DLI Manual Version 2.1.0
Page 15
- Usethe‘Test’ buttons to verify the intensity and temperature are correct, then select ‘Write Scene’ 11.2 RGBWAFColour RGBWAFabbreviatesRed,Green,Blue, White, Amber, and Free Colour. These six colors represent the output capabilities of compatible lights. - Ensure that the RGBWAF box is ticked. WSR-DLI Manual Version 2.1.0
Page 16
- Select the Scene to be adjusted - Using the slider, set the Intensity - Enter a value between 0-254 in each required input, representing Red, Green, Blue, White, AmberandFreeColour. WSR-DLI Manual Version 2.1.0
Page 17
- Test both the Intensity and RGBWAF by selecting the Test buttons to verify the light settings are correct - Select ‘Write Scene’ 12Colour Control (DT8) In Device Editor Whenaccesstotheballast configuration page is not possible or practical, Rako Channels can be adjusted for colour and temperature control in Rasoft Pro and the Rako App. 12.1 Setting an RGB Scene in Rasoft Pro - Select the Room which has the RGBWAF channels assigned. WSR-DLI Manual Version 2.1.0
Page 18
- Right-click the Channel number, and select “Set Channel type” > “RGB” - Select a Scene required to be changed. - Select the colour wheel. - Tick ‘Set RGB’. - Select the required colour. - Select the required intensity using the slider, and select “OK” WSR-DLI Manual Version 2.1.0
Page 19
- Select “Store Scene” - TheSceneisnowsetforthespecifiedcolour. 12.2 Setting a Temperature Scene in Rasoft Pro - Select the Room which has the RGBWAF channels assigned. - Right-click the Channel number, and select “Set Channel type” > “Tunable White” - Select the Scene to be changed. WSR-DLI Manual Version 2.1.0
Page 20
- Select the Tunable white icon for the Channel. - Tick “Set Tunable White”. - Adjust the temperature slide to the desired Level. - Select the intensity slider to the desired brightness. - ConfirmtheTemperatureandbrightness are correct, and select “OK” WSR-DLI Manual Version 2.1.0
Page 21
- Select “Store Scene” - TheSceneisnowsetforthespecifiedtemperature. 13Setting Colour and Temperature in the Rako App OncetheChannelshavebeenconfiguredinsection12,thedatacanbeuploadedtotheRako HUBtosetColourandTemperatureScenesintheRakoApp. For instructions on uploading Channel and Room information, see below: Wired Systems WK-HUBInstruction Manual - Section 6 Wireless Systems RK-HUBInstruction Manual - Section 6 13.1 Setting a Colour Scene in the Rako App - OpentheRakoApp,ConnecttotheHUB - Select the Room requiring the Scene change WSR-DLI Manual Version 2.1.0
Page 22
- Select the Scene number to change - Select the “LED” icon - Select “Edit Scene” - Select the desired colour using the colour wheel, and the brightness using the slider. WSR-DLI Manual Version 2.1.0
Page 23
- Select “Save Scene” 13.2 Setting Colour Tunable Scenes in the Rako App - OpentheRakoApp,ConnecttotheHUB - Select the Room requiring the Scene change - Select the Scene number to change - Select the ‘Tunable White’ Icon WSR-DLI Manual Version 2.1.0
Page 24
- Select ‘Edit Scene’ - Adjust the Temperature and Brightness sliders to the desired level. - Select “Save Scene” WSR-DLI Manual Version 2.1.0
Page 25
14Advancedfeatures of WSR-DLI 14.1 Swap Channels TwoDLIshort addresses can either be merged or swapped. Perform Swap will directly swap two DLI short addresses. Perform Move will take DLI Short Address 1 and merge it with DLI Short Address 2. 14.2 Visible Channels TheWSR-DLIwill allocate all 15 Channels in a Rako Room by default, if all 15 Channels are not being utilised, the number of allocated Channels can be reduced. To set the number of visible Channels, use the slider. The remaining channels can now be used for additional Rako devices. WSR-DLI Manual Version 2.1.0
Page 26
Appendix 1 - Hardware Changes PowerSupply WSR-DLIissueDandonwardsrequirea12VDCpowersupply WSR-DLIissueCandbelowrequirean18VDCpowersupply Appendix 2 - Recommended Wiring Topology There are several ways to wire the DLI bus when connecting ballasts to the WSR-DLI, it is recommendedtowireinaradialtopology which can be seen below: WSR-DLI Manual Version 2.1.0
Need assistance or looking to source this item?