This document could not be shown here. Open the PDF.
Text of this document7 pages · 587 words
Page 1
Instruction Manual WSR-DMX Wired DMXController 2024 Version 2.0.0
Page 2
For programming system programming information: Wired system setup guide. For a general overview: Wired RAK application sheet. Contents 1WhatistheWSR-DMX? 2Inputs 3Installation 4Terminations 5ProgrammingtheWSR-DMX 6Colour Wheel 1WhatistheWSR-DMX? TheWSR-DMXisa15-ChannelDMXcontrollerusedonaRako Wired network and can interface with DMX controllable devices such as RGBW lights and Fibre Optics. 2Inputs TheWSR-DMXhastwoinputoptionsfortheDMXinput connection, either an RJ45 cable can be used, or a suitable 2-core and shield cable. TheRakoWirednetworkalsohastwoconnectionoptions, either the RJ11 socket can be used with the supplied RJ11 cable, or a CAT5/CAT6 cable can be used on the daughterboard. NB It is essential to set the correct termination on the daughterboard if it is used, for more information, see Terminations. WSR-DMX Manual Version 2.0.0
Page 3
3Installation Installation should only be carried out by a competent electrician. STEP1 Removethecoverbyremoving the two screws at the bottom of the unit, pulling the bottom of the cover away from the bottom, andlifting it. Set the two cable clamps aside. STEP2 Connect the DMX Output. MakeaconnectiontotheRako Wired network via the RJ11 port using the supplied RJ11 cable, or by CAT5/CAT6 on the daughterboard on the top section of the WSR-DMX. NB It is essential to set the correct termination on the daughterboard if it is used, for moreinformation, see Terminations. STEP3 Fit the supplied cable clamps andensure the cable is unable to move. WSR-DMX Manual Version 2.0.0
Page 4
STEP4 Replace the cover and replace the screws. 4Terminations It is important to terminate WSR-DMX correctly otherwise the wired system will not function. Thetermination that is required depends on the nature of the installation and the position of the RAK-LINK within the system. NoTerm-BothJumpersremoved UsedwhentheWSR-DMXisnotattheendofline.Thisisusually identifiable by two cables being punched down to the WSR-DMX. Term-Jumperfittedacross1+2&4+5 UsedwhentheWSR-DMXis“endofline”inadaisychainconfiguration. Star Term - Jumper fitted across 2+3 & 5+6 UsedwhentheWSR-DMXis“endofline”inaSTARwireconfiguration. 5ProgrammingtheWSR-DMX Thefollowing steps assume: - AProject File has been created - Roomshavebeenadded - Channels have been added - AHUBoraRAMPIhasbeensetupasacommunicationsdevice WSR-DMX Manual Version 2.0.0
Page 5
If any of the above are still required, see the Wired system setup guide. - In Rasoft Pro, go to File > New Device - ADevicemenuwillpopup,selecttheWSR-DMXandselect‘Next’ - Give the WSR-DMX device a name and select ‘Next’ WSR-DMX Manual Version 2.0.0
Page 6
- Assign a Room and Channel and select ‘Next’ NB For more than one Channel, select the first Channel, subsequent Channels will automatically be assigned. - To put the device into setup mode, press and hold the button on the top right of the WSR-DMX,andtheLEDwillbegintoflash.Releasethebutton;theLEDshould continue to flash, and the setup wizard will show ‘Device Found’ - Select ‘Finish’, the device is now paired and in the project file. WSR-DMX Manual Version 2.0.0
Page 7
5Setting DMX Driver Addresses DMXdrivers require an address in order to be controlled by the WSR-DMX, the number which is set on the DMX driver will relate to the starting address in the Room the WSR-DMX is programmed in, for example: DMXDriverAddress RakoChannelNumber 001 1 002 2 003 2 004 3 005 4 NB Although the addressing structure above is the most common, DMX drivers vary in their configuration, read the manufacturer's instruction manual for specific instructions. 6Colour Wheel If the WSR-DMX is used for colour control, the outputs on the WSR-DMX can be controlled using a colour wheel in the Rako App, where selecting a colour will automatically mix the Channels without needing to do it individually. Thecolour wheel is not enabled by default, for a colour wheel to show in the Rako App, the Channels need to be labelled as below: Example: Acolour wheel in the App called “Feature” would have the following channel names: WSR-DMX Manual Version 2.0.0
Need assistance or looking to source this item?