This document could not be shown here. Open the PDF.
Text of this document8 pages · 618 words
Page 1
Instruction Manual RSR-DMX 15-Channel DMX Controller 2024 Version 2.2.0
Page 2
For more information relating to the RSR-DMX see the Wireless Module Application Sheet, Wireless RAK Application Sheet, and Wireless Device LED Diagnostics. For programming a Wireless system, including the device in this manual: Wireless Module Programming Guide Contents 1WhatistheRSR-DMX? 2Installation 3Initial Checks 4ProgrammingtheRSR-DMX 5Setting DMX Driver Addresses 6Colour Wheel Appendix 1 - Wiring Example 1WhatistheRSR-DMX? TheRSR-DMXisa15-Channelwireless controller which can interface with DMX interfaces such as colour-changing lights or fibre optics. 2Installation Installation should only be carried out by a competent electrician. RSR-DMXmodulesshouldbemountedinareasthatareadequatelyventilated,dry, andoutside of any metal-enclosed casings that may interfere with the wireless signal. Modulesshouldbemountedvertically, with the terminals at the bottom. Ensurethat cable clamps are securely fitted on the supply and load cables. Whilethemodulesaredesignedtobecompletelymaintenance-free, they should be mountedinanaccessible location should investigation or re-addressing of the units benecessary. RSR-DMX Manual Version 2.2.0
Page 3
STEP1: Removethecoverbyremoving the two screws at the bottom of the unit, pulling the bottom of the cover away from the bottom, andlifting it. Set the two cable clamps aside. STEP2: Connect the 12V PSU and the DMXOutput. TheRJ45portorthree-way terminal port may be used. STEP3: Fit the supplied cable clamps andensure the cable is unable to move. STEP4: Replace the cover and replace the screws. RSR-DMX Manual Version 2.2.0
Page 4
3Initial Checks Thesetupbutton can be used as a manual on/off switch to test the circuit. Theinternal LED on the unit will flicker when the module receives ANY Rako wireless message, which is a useful diagnostic indicator. This function becomes inactive after 20 minutes to avoid a nuisance light spill but can be re-activated by pressing the setup button. Should the module not respond to any of the above, further investigation must be made before proceeding any further. 4ProgrammingtheRSR-DMX Thefollowing steps assume: - AProject File has been created - Roomshavebeenadded - Channels have been added - AHUBoraRAMPIhasbeensetupasacommunicationsdevice If any of the above are still required, see the Wireless Module Programming Guide. 1. In Rasoft Pro, go to File > New Device 2. Adevice menu will pop up, select the RSR-DMX and select ‘Next’ RSR-DMX Manual Version 2.2.0
Page 5
3. Assign the RSR-DMX to the desired Room and Channel, and select ‘Next’ NB For more than one Channel, select the first Channel, subsequent Channels will automatically be assigned. 4. To put the device into setup mode, press and hold the button on the top right of the RSR-DMX,andtheLEDwillbegintoflash.Releasethebutton;theLEDshould continue to flash. 5. Select ‘Device is in setup’, this will send an ‘Ident’ command to the device in setup mode,oncethis is complete, the LED on the device should no longer be flashing. RSR-DMX Manual Version 2.2.0
Page 6
6. Select ‘Finish’, the device is now paired and in the project file. 5Setting DMX Driver Addresses DMXdrivers require an address in order to be controlled by the RSR-DMX, the number which is set on the DMX driver will relate to the starting address in the Room the RSR-DMX is programmed in, for example: DMXDriverAddress RakoChannelStarting Number 001 1 002 2 003 2 004 3 005 4 NB Although the addressing structure above is the most common, DMX drivers vary in their configuration, read the manufacturer's instruction manual for specific instructions. RSR-DMX Manual Version 2.2.0
Page 7
6Colour Wheel If the RSR-DMX is used for colour control, the outputs on the RSR-DMX can be controlled using a colour wheel in the Rako App, where selecting a colour will automatically mix the Channels without needing to do it individually. Thecolour wheel is not enabled by default, for a colour wheel to show in the Rako App, the Channels need to be labelled as below: Example: Acolour wheel in the App called “Feature” would have the following channel names: RSR-DMX Manual Version 2.2.0
Page 8
Appendix 1 - Wiring Example RSR-DMX Manual Version 2.2.0
Need assistance or looking to source this item?