This document could not be shown here. Open the PDF.
Text of this document8 pages · 733 words
Page 1
Instruction Manual RLED30CV4+ 4-Channel Constant Voltage Dimmer 2024 Version 2.0.1
Page 2
For more information relating to the RLED30CV4+, see the Wireless Module Application Sheet, Wireless RAK Application Sheet, and Wireless Device LED Diagnostics. For programming a Wireless system, including the device in this manual: Wireless Module Programming Guide Contents 1. What is the RLED30CV4+? 2. Loadings 3. Installation 4. Initial Checks 5. Programming the RLED30CV4+ 5.1 Adding the RLED30CV4+ into Rasoft 5.2 Output types 5.3 Setting the device output 6. Appendix 1: LED Diagnostics 1WhatistheRLED30CV4+? TheRLED30CV4+isaconstantvoltagedimmerwithfour individually controllable outputs, typically used for constant voltage loads, such as colour-changing LED tape. There are four modes of operation: 4RakoChannelsRGBW 1RakoChannelRGBW* 1RakoChannelRGB* 1RakoChannelColourTunable* *Requires latest version of Rasoft Pro 2Loadings Voltage Wattage 12VDC 30WperChannel 24VDC 60WperChannel RLED30CV4+ Manual Version 2.0.1
Page 3
3Installation Installation should only be carried out by a competent electrician. DONOTCONNECTDIRECTLYTOTHEMAINSSUPPLY. RLED30CV4+modulesshouldbemountedinareasthatareadequatelyventilated, dry, and outside of any enclosed metal casings that may interfere with the Wireless signal. Modulesshouldbemountedvertically, with the terminals at the bottom, or horizontally. Whilethemodulesaredesignedtobemaintenance-free, they should be mounted in an accessible location should investigation or re-addressing of the units be necessary. Ensurethat the cable clamps are fitted tightly to secure the cables. Theunitinputvoltage is 12V or 24V DC, and the power supply must be adequately rated for the connected load. STEP1 Removethecoversand cable clamps. STEP2 Connect the 12/24V power supply to the ‘DC Input’ terminals. STEP3 Option 1 - RGBW Connect the constant voltage load. TheRLED30CV4+hasa commonpositive, and four independent negative connections. Option 2 - Colour Tunable Whenconnectingcolour tunable LEDs, Outputs A andCarecontrolled together, as are B and D. RLED30CV4+ Manual Version 2.0.1
Page 4
STEP4 Secure the cables with the cable clamps provided. STEP5 Replace the covers. 4Initial Checks Whenpowerisinitially connected to the module, the load should power up to full brightness on all outputs. Theclearbuttoncanbeusedasamanualon/offswitchtotestthecircuits. Theinternal LED behind the clear button will flicker when the module receives any Rako Wireless message and is a useful diagnostic indicator. The LED feedback becomesinactive after 20 minutes to avoid a nuisance light spill but can be re-activated by pressing the clear button. 5ProgrammingtheRLED30CV4+ OncetheRLED30CV4+haspoweredupandhasbeentestedworkingwiththesetup button, the device is ready to be programmed. Ensure that a project file has been created, and Rasoft Pro is connected to a programming device such as a RAMPI or HUB. For more information, see the Wireless Module Setup Guide. RLED30CV4+ Manual Version 2.0.1
Page 5
5.1 Adding the RLED30CV4+ into Rasoft 1. In Rasoft Pro, go to File > New Device 2. Adevice menu will pop up, select the RLED30CV4+ and select ‘Next’ 3. Assign the RLED30CV4+ to the desired Room and Channel, and select ‘Next’ NB For more than one Channel, select the first Channel, subsequent Channels will automatically be assigned. RLED30CV4+ Manual Version 2.0.1
Page 6
4. To put the device into setup mode, press and hold the clear button on the RLED30CV4+,andtheLEDwillbegintoflash.Releasethebutton;theLEDshould continue to flash. 5. Select ‘Device is in setup’, this will send an ‘Ident’ command to the device in setup mode,oncethis is complete, the LED on the device should no longer be flashing. 6. Select ‘Finish’, the device is now paired and in the project file. 5.2 Output types TheRLED30CV4+canbeconfiguredindifferentwaysdependingontheloadtype,there are four options in Rasoft Pro. 1. RGBW(4Channels)-Fourcontrollable Rako Channels in the Room Editor and the App. RGBW4ChannelMode 2. RGBW(1Channel)-OneChannelintheRoomEditorandtheApp,thecolourcan beset using a separate colour wheel by selecting the RGBW symbol on the Channel slider or by using the colour wheel on the app. RGBW1ChannelMode RLED30CV4+ Manual Version 2.0.1
Page 7
3. RGB(1Channel)-Similar to the RGBW single Channel output, only omitting white. RGB1ChannelMode 4. Colour Tunable (1 Channel) - Used when there are two temperatures of LED load, controllable via the Colour Tunable icon to the right of the Channel name, as well as in the App. NB Outputs A and C are used for Cool White, B and D are used for Warm White. Colour Tunable 1 Channel Mode 5.3 Setting the device output 1. Select the RLED30CV4+ in the device editor 2. Select the ‘Output Options’ tab. 3. From the dropdown menu, select the desired output option. RLED30CV4+ Manual Version 2.0.1
Page 8
6Appendix1:LEDDiagnostics Wireless Range LEDPulses Description GoodWireless reception Whentheunitis receiving successfully, there will be four rapid pulses on the LED whenanyWireless messageissent. BadWireless reception Whentheunitis out of range, there will be intermittent pulses on the LEDwhenanyWireless messageissent. NB It is recommended to install aWireless repeater (WRB-100)if you are experiencing intermittent Wireless range. Should the module not respond to any of the above, check the supply voltage. RLED30CV4+ Manual Version 2.0.1
Need assistance or looking to source this item?