This document could not be shown here. Open the PDF.
Text of this document8 pages · 635 words
Page 1
Instruction Manual RAMVR Wireless PIR Interface 2024 Version 2.1.0
Page 2
For more information relating to the RAMVR, see the Wireless Module Application Sheet, Wireless RAK Application Sheet, and Wireless Device LED Diagnostics. For programming a wireless system: Wireless Module Setup Guide Contents 1WhatistheRAMVR? 2Inputs 3Installation 4ProgrammingtheRAMVR 4.1 Assigning the RAMVR 4.2 Configuring the RAMVR 1WhatistheRAMVR? TheRAMVRisaRakoWirelessinterface module that integrates 3rd party presence sensors to switch Rako commands. There are two wiring options for the RAMVR depending on the type of PIR used, volt-free or mains. NB Donotuseboththevolt-free PIR side and the mains PIR side at the sametime. 2Inputs RAMVR Manual Version 2.1.0
Page 3
3Installation Installation should only be carried out by a competent electrician. RAMVRmodulesshouldbemountedinareasthatareadequatelyventilated,dry, andoutside of any enclosed metal casings that may interfere with the wireless signal. Modulesshouldbemountedvertically, with the terminals at the bottom, or horizontally. Whilethemodulesaredesignedtobemaintenance-free, they should be mounted in an accessible location should investigation or re-addressing of the units be necessary. Ensurethat the cable clamps are fitted tightly to secure the cables. STEP1 Removethefront covers and set the cable clamps aside. STEP2 Chooseeither option 1 wiring or option 2 wiring depending on the type of PIR. Option 1: Volt-free PIR’s Option 2: Mains PIR’s NB Checkwith the PIR manufacturer for compatibility before connecting to the RAMVR. RAMVR Manual Version 2.1.0
Page 4
STEP3 Replace the covers and cable clamps, and ensure that any of the cables connected to the RAMVR are secure. If the RAMVR is wall-mounted, secure the unit into the bracket provided. 4ProgrammingtheRAMVR Thefollowing steps assume: - AProject File has been created. - Roomshavebeencreated. - TheHUBhasbeenconfigured. - TheChannels in the Rooms have been labelled. If the above has not been done, refer to the Wireless Module Programming Guide before continuing. 4.1 Assigning the RAMVR - Select “File” - “New device” to bring up the “New device Wizard” RAMVR Manual Version 2.1.0
Page 5
- Select “RAMVR” and then select “Next”. - Associate the RAMVR with a Room using the drop-down menu, leave “Associate to Channel” as it is and select “Next”. RAMVR Manual Version 2.1.0
Page 6
- Put the RAMVR into Setup Mode by pressing and holding the setup button on the unit for 3-4 seconds. - OncetheRAMVRhasenteredSetupMode,theblueLEDontheunitwillblink periodically, select “Device is in setup” > “Finish”. - TheRAMVRhasbeenassignedinRasoftPro,itcanbeaccessedbyselectingit in the “Device List”. RAMVR Manual Version 2.1.0
Page 7
4.2 Configuring the RAMVR TheRAMVRprogrammingoptionsarefoundonthedeviceeditorwhichisaccessedby selecting it in the Device List. MovementAction 1. Action - Select the Scene from the drop-down menu which is to be triggered when the PIR detects movement. 2. Only if lights are off - When enabled, the PIR will only trigger a Scene if it has received an off command from another source such as a keypad or via the App. 3. 30 Second Exit Delay - When the RAMVR receives an off command, the ‘Action’ will not trigger for 30 seconds even when there is movement, this is typically used to prevent nuisance triggering and gives enough time for the occupant to leave the Room. 4. Use as absence detector - If movement has not been detected for the specified duration of the ‘Auto-Off Trigger’ then the RAMVR will send the Auto-Off command. Whenabsencedetectionis enabled, ‘Actions’ on the RAMVR are disabled. Auto-Off Trigger RAMVR Manual Version 2.1.0
Page 8
1. Auto turn lights off after - When enabled, the specified time will reset upon movementdetection and begin counting down, once the timer reaches 0s the ‘Action’ command will be triggered. The timeout can be temporarily disabled by sending an ‘Off’ command from a keypad programmed to the same Room. 2. Disable Auto-Off Whenenabled,an‘Off’ commandis received by the RAMVR will disable the countdowntimer, this is reinstated when the RAMVR receives a Scene command. 3. Action Select the ‘Off’ command which will be triggered when the PIR times out, although this is almost always ‘Off’, it can be set to a Scene if required. RAMVR Manual Version 2.1.0
Need assistance or looking to source this item?