Lutron Lamp Dimmer HQRK-P20-240 – installation instructions (043549 Rev. A)

Page 1

Installing the lamp dimmer Using the HomeWorks system Error Codes – Red • Hybrid repeater (HQx-REP) is required for load control to work in a HomeWorks system. Blink pattern Probable Cause Turn the lamp ON and unplug the cord from the wall outlet ... ... = on = off 1 • System programming and activation (addressing) must be done through the HomeWorks software. ... ... ... • Product may be permanently damaged. P/N 043549 Rev A English WARNING - Electric Shock Hazard - ... ... ... ! To avoid the risk of electrical shock, do • Unsupported bulb type (dimmer not rated for magnetic not open, cut cord, or rewire the lamp ... low-voltage loads). ... 9 m (30 ft) ... dimmer. Modification of the module can ... ... ... Lamp Dimmer maximum Radio Powr Radio Powr result in personal injury or death. Savr sensor Savr sensor • Lamp may be shorted. ... • Circuit has too much load. ... HQRK-P20-240 ... ... ... 220 – 240 V~ 50 / 60 Hz WARNING - Electric Shock Hazard - ... Hybrid Repeater ! Hybrid Repeater Hybrid Repeater • Circuit has too much load. To avoid the risk of electrical shock, Hybrid Pico Hybrid Pico Repeater Status Repeater Status • Inadequate ventilation around lamp dimmer. P 1 2 3 4 ... P 1 2 3 4 ... ... wireless unplug the lamp dimmer when changing Communication wireless Communication repeater RF Wired repeater RF Wired Setup Test Activate Setup Test Activate Test Add ... Test Add control light bulbs. Changing light bulbs with the control Power Repeater Link Power Repeater Link 9 V CO 24 MUMU 9 V CO 24 MUMU 1 A 200 W power on could result in personal injury M1 V2X3 X4 M1 V2X3 X4 LED 150 W or 1 A Max. or death. DEL Incandescent / LED * Lamp Halogen dimmer Lamp IMPORTANT NOTES dimmer WARNING - Entrapment Hazard - To avoid the risk of entrapment, serious injury, or death, these 9 m (30 ft) controls must not be used to control equipment which is not visible from every control location or Load Type: The lamp dimmer is designed to dim one maximum which could create hazardous situations such as entrapment if operated accidentally. Examples of such LED, incandescent, or tungsten halogen table or floor Plug the lamp cord into the lamp dimmer receptacle RF Link equipment which must not be operated by these controls include (but are not limited to) motorized gates, lamp. Use with LAMPS ONLY. It is recommended to 2 305 m (1000 ft) maximum plug the lamp directly into the dimmer receptacle and not wire length per run 18 m (60 ft) maximum garage doors, industrial doors, microwave ovens, heating pads, etc. It is the installer’s responsibility to ensure that the equipment being controlled is visible from every control location and that only suitable through a multi-plug adaptor, power strip, or extension equipment is connected to these controls. Failure to do so could result in serious injury or death. cord. Do not use to control a lamp that contains an integral Lamp Dimmer Environment: Ambient operating temperature: 0 °C to 40 °C (32 °F to 104 °F), dimmer or a touch lamp. For a lamp with an integral 3-way 0% to 90% humidity, non-condensing. Indoor use only. switch, the switch should be set to full on position. The Cleaning: To clean, wipe with a clean damp cloth. DO NOT use any chemical cleaning solutions. lamp dimmer is compatible with trailing-edge loads. Not RF Device Placement: Lamp dimmer must be located within 9 m (30 ft) of an RF signal repeater. rated for magnetic low-voltage loads. Pairing the lamp dimmer and Pico * LED Load Capacity: LED current ratings must be below wireless control without a system Hereby, Lutron Electronics Co. Inc., declares that the radio equipment type HQRK-P20-240 is in compliance 1 A. If no current rating is available, wattage must be with Directive 2014/53/EU below 150 W. The full text of the EU declaration of conformity is available at the following internet address: Lutron.com/cedoc Lamp Cord Lamp Dimmer Receptacle Press and hold the button on lamp dimmer 1 Troubleshooting If using LED bulbs, we Symptoms Probable cause recommend that they are • Light bulb(s) burned out. Lutron compatible. Insert the plug of the lamp dimmer into the wall outlet Hold for 6 seconds until • Breaker is OFF or tripped. 3 LED starts blinking. For the list of compatible LED bulbs, Lamp does not turn on. • Light not properly installed. please visit www.lutron.com/LEDtool • The switch on the lamp has been turned off. • Error has occurred. See Error Codes section for For advanced features, tips for using LEDs, the Lamp more information. complete HomeWorks product line, and more, please Dimmer Plug • System devices are too far apart. A Lutron visit www.lutron.com wireless repeater may be needed to extend the Press and hold the “off” button on Pico wireless control Help 2 wireless range. • The lamp dimmer is already at the light level the Pico wireless control is sending. Europe: +44.(0)20.7702.0657 Hold for 6 seconds until x3 Repeat steps to pair other • The Pico wireless control is outside the 9 m lights flash 3 times. Pico wireless controls. Lamp does not respond to Pico (30 ft) operating range. Asia: +91.124.439.0130 wireless control. • The Pico wireless control battery is low. U.S.A. / Canada: 1.844.LUTRON1 • The Pico wireless control battery is installed incorrectly. Mexico: +1.888.235.2910 Turn the lamp dimmer ON using the toggle button • The switch on the lamp has been turned off. Set the light level on the Pico wireless control Others: +1.610.282.3800 4 3 • Error has occurred. See Error Codes section for Fax: +1.610.282.6311 more information. Adjust light to Press and hold the favorite button for 6 seconds Status LED desired level. to save the current light level. Tap the favorite • Bulbs turn off while being dimmed. • Verify LED bulbs are marked dimmable. Visit Limited Warranty: Green – Blinks when load is toggled button at any time to recall saved level. • Bulbs turn on at high light level but www.lutron.com/LEDtool for a list of www.lutron.com/TechnicalDocumentLibrary/Intl_Warranty.pdf Flashes during association do not turn on at a low light level. recommended LED bulbs. Red – Blinks when error • Bulbs flicker or flash when • Low-end trim may need to be adjusted for best ©2020 Lutron Electronics Co., Inc. dimmed to a low light level. LED bulb performance. Trim can be adjusted in the Lutron app. The Lutron logo, Lutron, Pico, Radio Powr Savr and TRA HomeWorks are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other Toggle Button Return to factory settings countries. Press to toggle ON / OFF REGISTERED NO: Apple is a trademark of Apple Inc., registered in the ER89916/20 1. Quickly triple tap the toggle button on the lamp dimmer, holding on the third tap. U.S. and other countries. App Store is a service mark of DEALER NO: 2. Once the bulb starts to flash, release the toggle button and immediately triple Apple Inc. tap it again. 0016561/08 3. The bulb will flash and the lamp dimmer will be returned to its factory settings.