This document could not be shown here. Open the PDF.
Text of this document5 pages · 840 words
Page 1
product specifications 369351c 04.27.16 HomeWorksR QS Hybrid Repeaters HomeWorksR QS Hybrid Repeaters add wireless Radio Frequency (RF) communication and extend the range of RF signals that are sent between dimmers, switches, keypads, visor control receivers, shades / draperies, and other devices. Repeaters ensure error-free communication between system components and prevent interference from neighboring systems. The first repeater connects to the HomeWorksR QS processor to provide RF communication that extends up to 30 ft (9 m) in every direction. Up to four (4) total Hybrid Repeaters can be used per link to extend the RF range for larger system applications. Each Repeater has an RF range of 30 ft (9 m) between repeater and devices or 60 ft (18 m) between repeaters, covering a total area of approximately 2500 sq ft (232 m(). Model Numbers Frequency HQR-REP-120 434 MHz HQk-REP 868 MHz HQm-REP 868 MHz Limited HQn-REP 865 MHz HQR-REP-120-BA 434 MHz (Brazil) HQQ-REP 434 MHz Limited Only available in White (WH). HomeWorksR QS software will select the correct frequency/channel code for compatibility with your particular geographic region. | www.lutron.com/help Lutron® 1
Page 2
product specifications 369351c 04.27.16 HomeWorksR QS Hybrid Repeaters Specifications Model Number HQR-REP-120; HQk-REP; HQm-REP; HQn-REP; HQR-REP-120-BA; HQQ-REP Power Hybrid Repeater: DC adapter: 9 V- 300 mA Link: 24 V- 50 mA DC adapter: Input: 100-240 V~ 50/60 Hz 6.5 W Output: 9 V- 300 mA Typical Power Hybrid Repeater: 0.6 W Consumption Test conditions: one LED on, powered by a 9 V- adapter. Regulatory Approvals Hybrid Repeater: FCC, IC, COFETEL, CE, CCC, TRA, CTICK, ANATEL, IDA, SUPERTEL, SUTEL Environment Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C), 0% to 90% humidity, non-condensing. Indoor use only. Unit generates heat, maximum 4 BTU/hr Low-Voltage Wire Type Two pair – one pair 18 AWG (1.0 mm2), one pair 22 AWG to 18 AWG 2 2 (0.5 mm to 1.0 mm ) twisted shielded – NEC® Class 2 / PELV cable. Required for connecting the first repeater to the processor and may be used to connect additional Hybrid Repeaters. Communications The first Hybrid Repeater communicates with the HomeWorksR QS processor on the RF wired link. Subsequent Repeaters may be wired on this link or may communicate over Radio Frequency (RF). All RF devices must be located within 30 ft (9 m) of a Repeater. All Repeaters must be within 60 ft (18 m) of another Repeater. ESD Protection Tested to withstand electrostatic discharge without damage or memory loss, in accordance with IEC 61000-4-2. Surge Protection Tested to withstand surge voltages without damage or loss of operation, in accordance with IEEE C62.41-1991 Recommended Practice on Surge Voltages in Low-Voltage AC Power Circuits. Power Failure Power failure memory: should power be interrupted, the Repeater will return to its previous state when power is restored. Mounting Mount on a wall, ceiling, or level surface using the two #6 (M3) screws provided. Connections Hybrid Repeater: RS485 Warranty www.lutron.com/TechnicalDocumentLibrary/warranty.pdf Design Features • Test button - enters the RF repeater test mode. • RS485 port to connect to the HomeWorksR • Activate button - provides repeater activation QS RF link and to other repeaters through a within system. wired link (daisy-chain). | 2 Lutron® Customer Assistance: 1.800.LUTRON1
Page 3
product specifications 369351c 04.27.16 HomeWorksR QS Hybrid Repeaters Dimensions Measurements shown as: in (mm) Front View Side View see table below 1 5 ⁄4 1/4 (133) (6) 3 2 ⁄4 (70) mounting Holes 3 1 3 ⁄4 (95) 1 ⁄16 (27) 1 4 ⁄4 (108) Model Dimension HQR-REP-120, HQR-REP-120-BA, 6.25 (158.8) HQQ-REP Mounting HQK-REP, HQM-REP, HQN-REP 3.13 (79.4) Vertical Horizontal Ceiling #6 (m3) screw recommended Wall (2 included) Level Surface | www.lutron.com/help Lutron® 3
Page 4
product specifications 369351c 04.27.16 HomeWorksR QS Hybrid Repeaters Operation Repeater Status LEDs Displays the activation status or test status of the Repeaters in the system. RF and wired LEDs Displays the Tx / Rx activity on the RF and wired links. (Green=Tx; Orange=Rx) Test and Activate Buttons Press and hold to enter the system into Test mode or Activate mode. Test and Activate LEDs Flashes green to indicate that the system is in Test mode or Activate mode. Wired and RF Configuration Hybrid Repeater 30 ft (9 m) 30 ft (9 m) 30 ft (9 m) maximum maximum maximum RF Link Wired Link (Daisy-chain) 60 ft (18 m) 1000 ft (305 m) maximum maximum IEC PELV / nECR Class 2 cable Two pair – one pair 18 AWG 2 (1.0 mm ), one pair 22 AWG to 2 2 18 AWG (0.5 mm to 1.0 mm ) twisted shielded. | 4 Lutron® Customer Assistance: 1.800.LUTRON1
Page 5
product specifications 369351c 04.27.16 HomeWorksR QS Hybrid Repeaters Connections Top View RF range: To Repeater: 60 ft (18 m) To other devices: 30 ft (9 m) Bottom View Wired Link (Daisy Chain) maximum 1000 ft (305 m) COm 24 V Power Input mUX mUX Power Jack (to adapter) NOTE: Power must be provided by a IEC PELV / NECR Class 2 9 V- adapter or 24 V- power on the HomeWorksR QS processor link. | www.lutron.com/help Lutron® 5
Need assistance or looking to source this item?