Future Automation RTE-FSA technical sheet

Page 1

EDIT CUSTOM PROPERTIES 29. TITLE TO DESIRED RTE-FSA PRODUCT CODE RTE FIBRE SPOOL ASSEMBLY 30. SUBHEADING TO DESIRED PRODUCT DESCRIPTION EDIT CUSTOM PROPERTIES TECHNICAL SHEET 31. ISSUE NO. UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 002 TO DESIRED ISSUE NUMBER WWW NET . . SHEET 1 FUTUREAUTOMATION

Page 2

RTE-FSA RTE FIBRE SPOOL ASSEMBLY SUPPORT FOR FIBRE INSTALLATIONS The RTE-FSA kit is designed to provide a dedicated location in the RTE enclosure for fibre cables to be route and spooled. Minimum spool diameter is 93mm (3 5/8"). There is simple cable strain relief as cables are routed up to the keystone connections above. FIBRE CABLES SHOULD ENTER THE RTE ENCLOSURE FROM BELOW TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 002 WWW NET . . SHEET 2 FUTUREAUTOMATION

Page 3

RTE-FSA RTE FIBRE SPOOL ASSEMBLY CONFIGURABLE DESIGN The RTE Fibre Spool Assembly can be installed with a two layer configuration, for extra cable capacity and separation. It can also be configured in a wider setup to create a larger spool and take more cable length on the spool. Closed spool configuration = 292mm / 11.5" of cable per loop Open spool configuration = 7/8" 380mm / 15" of cable per loop 23 15/16" 24 1 7/8" 48 Cable tie slots for strain relief on cables 7/8" 23 TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 002 WWW NET . . SHEET 3 FUTUREAUTOMATION

Page 4

RTE-FSA RTE FIBRE SPOOL ASSEMBLY 11 5/8" DIMENSIONS 295 3/8" 10 The RTE Fibre Spool Assembly can be installed with a two layer configuration, for extra cable capacity and separation. It can also be configured in a

wider setup to create a larger

spool and take more cable length 57 2 1/4" on the spool.

190 7 7/16"

Closed spool configuration = 292mm / 11.5" of cable per loop Open spool configuration = 380mm / 15" of cable per loop 4 3/4" 2 1/8" 120 53 8 3/4" 222 9/16" 15 1/8" R3

190 7 7/16"

1 1/8" 1 11/16" 11/16" 1 11/16" 29 43 18 43 12 1/16" 307 TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 002 WWW NET . . SHEET 4 FUTUREAUTOMATION

Page 5

RTE-FSA RTE FIBRE SPOOL ASSEMBLY RTE7 LOCATION IN ENCLOSURE Primarily, the RTE-FSA assembly is designed to be fitted at the bottom of the RTE7 enclosure. This utilises the space available at the bottom of the enclosure. The RTE-FSA can be fitted in the RTE4, but this will impede some cables running to the lower 2 1/8" hinging connectors. In the RTE4, only one fibre spool assembly can be installed. 54 In the RTE7, a maximum of two fibre spool assemblies can be installed - however, the upper assembly would impede cables running to the lower hinging connectors. RTE4

189 7 7/16"

2 1/8" B 3/8" 54 104 10

4 1/16"

292 3/8" 11 1/2" 10

189 114 7 7/16" 4 1/2"

253 A 9 15/16"

189 7 7/16"

253 9 15/16"

SECTION B-B

114 4 1/2" SECTION A-A

4 3/4" 120 A TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 B ISSUE 002 WWW NET . . SHEET 5 FUTUREAUTOMATION