This document could not be shown here. Open the PDF.
Text of this document15 pages · 1,994 words
Page 1
PS80 MANUAL ARTICULATING WALL MOUNT INSTALLATION INSTRUCTIONS ISSUE 004
Page 3
SAFETY DISCLAIMER IMPORTANT SAFETY INSTRUCTIONS BELOW WARNING: Failure to provide adequate structural strengthening, prior to installation can result in serious personal injury or damage to the equipment. It is the installer’s responsibility to ensure the structure to which the component is affixed can support four times the weight of the component and any additional apparatus mounted to the component. WARNING: Do not exceed the weight capacity for this product as listed below. This can result in serious personal injury or damage to the equipment. It is the installer’s responsibility to ensure that the total combined weight of all attached components does not exceed that of the maximum figure stated. WARNING: Risk of death or serious injury may occur when children climb on audio and/or video equipment or furniture. A remote control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over on to the child. WARNING: Risk of death or serious injury may occur. Relocating audio and/or video equipment to furniture not specifically designed to support audio and/or video equipment may result in death or serious injury due to the furnishing collapsing or over turning onto a child or adult. WARNING – RISK OF INJURY! Only for use with equipment weighing 265LBS (120KG) OR LESS. Use with heavier projectors/equipment may lead to instability causing tip over or failure resulting in death or serious injury. Bracket Suitable for Residential and Commercial Use. ADDITIONAL WARNINGS: 1. Keep all documentation/instructions after fitting. 2. Read all technical instructions fully before installation and use. It is the installer’s responsibility to ensure that all documentation is passed on to the end user and read fully before operation. 3. Do not use near water or outdoors unless the product has been specifically designed to do so. 4. Protect any cables or cords being used near this bracket from being walked on or pinched to prevent damage and risk of injury. 5. Use this product only for its intended purpose as described in the product instructions and only use attachments/ accessories specified by the manufacturer. 6. Do not operate the product if it is damaged in any way, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Contact the original installer/manufacturer to arrange repair or return. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons: 1. Clean only with a dry cloth and always unplug any electrical items being used in conjunction with this product before cleaning. Future Sound & Vision trading as Future Automation intend to make this and all documentation as accurate as possible. However, Future Automation makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without prior notice or obligation of any kind. Future Automation makes no representation of warranty, expressed or implied, regarding the information contained herein. Future Automation assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. 1
Page 4
PRODUCT WARRANTY & RISK ASSESSMENT WARRANTY INFORMATION WARNING - The warranty offered for this product shall be annulled if the product is used improperly or in a way that is in breach of our Terms of Service. Future Automation provides warranty for the mechanism you purchased for the period of 24 months from the date of purchase, provided that it isn’t used for unintended purposes. Under the warranty, Future Automation aims to either solve the issue remotely (via telephone or email support) or if the mechanism requires a part, arrange a visit to your premises by a Future Automation approved engineer or send replacement items where appropriate. Warranty repairs will be carried out as quickly as possible, but subject to parts availability. This warranty period is respectively extended for the period of a repair. A malfunctioning product must be cleaned and placed into suitable packaging to protect against transit damage before organising delivery to a repair workshop. All the complaints about defects must be submitted to the vendor/installer that sold this product, rather than directly to the manufacturer. Any part of your system that needs to be replaced during a warranty repair becomes the property of Future Automation. The warranty does not cover the following: • Damages resulting from improper product use or maintenance. • Repairs carried out by unauthorized persons. • Natural wear and tear during operation. • Damages caused by the buyer. • Accidental damages caused by a customer or damages caused as a result of careless attitude or usage, or damages caused by natural disasters (natural phenomena). • Any electrical, or other environmental work external to your Future Automation mechanism including power cuts, surges etc. • Additional items not supplied by Future Automation although they may have been supplied together by the retailer • Any 3rd party software products controlling your mechanism • Any transfer of ownership. Warranty is provided only to the initial purchaser. • Compensation for loss of use of the product, and consequential loss of any kind. A separate Safety and Servicing Information document is provided with these instructions (additional copies can be found at www.futureautomation.co.uk/safety), and this document MUST be filled out by the approved Future Automation Dealer who is installing the product. This Warranty Sheet must be held by the end user for the duration of the products life and will be referred to during servicing or warranty queries. The Safety and Servicing Information document also contains two Service History Forms that must be filled in by the approved Future Automation dealer who is performing the first required yearly service of this product. One copy of the Service History Form must be held by the customer (along with the Warranty Sheet) and a duplicate copy must be held by the approved Future Automation dealer that performed the service. Missing and/or mismatching documents may delay or invalidate warranty claims. Additional Service History Forms can be found on the Future Automation website for further yearly services. RISK ASSESSMENT INFORMATION It is the installer’s responsibility to perform a risk assessment of installed products. Future Automation can provide guidelines to installers/dealer about what should be included in a risk assessment, but due to the individual nuances of each location/site, Future Automation cannot provide a full list of areas to risk assess. For full risk assessment and safety information please view our Safety and Servicing guide available at www.futureautomation.net/safety 2
Page 5
GUIDE CONTENTS SAFETY DISCLAIMER 1 PRODUCT WARRANTY & RISK ASSESSMENT 2 GUIDE CONTENTS 3 PACKAGE CONTENTS 4 CALCULATING MOUNTING HEIGHT 5 SURFACE MOUNTING 6 ASSEMBLING THE SCREEN MOUNT 7 CABLE MANAGEMENT 8 ASSEMBLING UPRIGHTS 9 FITTING THE SCREEN 10 LEVELLING THE SCREEN 11 FRICTION ADJUSTMENT 12 3
Page 6
PACKAGE CONTENTS 1 - PS80 BRACKET 1.1 - WALL PLATE 1.2 - SCISSOR ARMS 1.3 - SCREEN MOUNT UPRIGHTS 1.4 - SCREEN MOUNT CROSSBARS 1.5 - PIVOT SHAFT ITEMS NOT SHOWN ON PAGE PS80 ACCESSORY PACK: - SCREEN FIXINGS PACK (MULTI-PACK OF NUTS, BOLTS, SPACERS AND WASHERS) - PACK OF CABLE TIES 1.2 1.4 1.1 1.3 1.3 1.4 1.5 4
Page 7
CALCULATING MOUNTING HEIGHT Dimension X Offer the PS Bracket up to the back of the screen, lining up the screen's VESA holes with the corresponding slots on the PS Bracket Screen Mount. Measure from the top of the screen, down to 1the top mounting hole on the Wall Plate (Dimension X as indicated above) to determine positioning of the top wall fixing holes. 5
Page 8
SURFACE MOUNTING The top fixing hole for the PS80 Bracket wall plate should be located the distance of Dimension X (measured on page 5) down from the top of the screen position. For ease of access, the scissor arms 1can be pulled out and fixed in place by inserting a screwdriver (or similar) into the side of the wall plate as shown below. Fix through the top two Ø10mm [0.4”] fixing holes in the Wall Plate to secure it to the wall. Once checking the bracket is level on the wall, secure the bracket using the remaining six fixing holes using 2suitable fixings (NOT SUPPLIED) as indicated below. Use a screwdriver or similar to hold the scissor arms open. 6
Page 9
ASSEMBLING THE SCREEN MOUNT The PS80 Screen Mount Frame is shipped in kit form and will need to be assembled for mounting. Attach each Mount Cross Bar to either end of the Pivot Shaft - The Pivot shaft must pass through 1 the larger hole in each Mount Cross Bar and be secured in place with the provided M8 bolts. NOTE: THE PROVIDED THRUST WASHER MUST BE SLID ONTO THE PIVOT SHAFT BEFORE FITTING THE TOP MOUNT CROSS BAR. 7
Page 10
CABLE MANAGEMENT Power and signal cable wall sockets should be kept outside of the footprint of the bracket to 1 maximise space available for cable routing - see Tech/ CAD files for bracket dimensions. All cables should enter the bracket at the top of the Wall Plate, run down each of the outer Scissor Arms and attach to the rear of the Screen Frame as shown below. Use supplied 2 cable ties to secure all cables to the Scissor Arms and Screen Mount. 3 Ensure sufÏcient slack is left at the top pivot point of the bracket. Ensure sufÏcient slack is left where the cables span between the Scissor Arm and the Screen Frame. Fully advance and rotate the bracket in both directions to ensure cables do not restrict 4 movement. Ensure sufÏcient cable slack here. Ensure sufÏcient cable slack here. Ensure sufÏcient cable slack here. 8
Page 11
ASSEMBLING UPRIGHTS 1 Inside the bolt pack will be an aluminium height adjustment boss and three M6x16mm button head bolts. 2 Ensure the internal hex of the grub screw is facing up and tighten the three bolts using a 4mm allen key. 4 mm 9
Page 12
FITTING THE SCREEN Lay the screen face down on a padded surface and place the Screen Mount Uprights onto the screens four mount holes. Secure the Screen Mount Uprights to the back of the screen, using 1 the bolts and washers provided in the Fixings Pack as shown below. If the screen has recessed mount holes or if you need to space the uprights off for clearance, use the spacers provided in the Fixings Pack. NOTE: Screens that do not have standard VESA bolt patterns may require an adapter plate. Top Of Screen Lift the Screen and Screen Mount Uprights up and onto the Screen Mount Crossbars of the PS 2 Bracket. 10
Page 13
LEVELLING THE SCREEN 1 The screen uprights have a grub screw that can be adjusted to allow the screen to be levelled. Loosen all four pinch bolts and adjust 2 grub screws until the screen sits level. 4 mm 3 When the screen is level remember to re-tighten all four pinch bolts. Connect all power and signal cables to Screen and check that enough slack has been left for the full range of motion of the bracket. 11
Page 14
FRICTION ADJUSTMENT Once fitted, if you find that the PS bracket's pull function is too stiff or too loose, the friction can be adjusted using the bolt on the left side of the bottom sliding collar as shown below. 1 Loosen the grub screws to decrease friction, or tighten to increase friction. Bottom Sliding Collar Friction Adjustment Bolt 12
Page 15
EUROPEAN OFFICE NORTH AMERICAN OFFICE Address: Address: Unit 6-8 Enterprise Park Brunel Road 127 Venture Drive Bedford Dover Bedfordshire NH MK41 9TG 03820 Phone: +44 (0) 1438 833577 Phone: +1 (603) 742 9181 Email: info@futureautomation.co.uk Email: info@futureautomation.net OfÏce Hours: OfÏce Hours: Mon - Fri 8:00 to 17:30 GMT Mon - Fri 7:00 to 17:00 EST Saturday & Sunday - Closed Saturday & Sunday - Closed www.FUTUREAUTOMATION.net
Need assistance or looking to source this item?