This document could not be shown here. Open the PDF.
Text of this document22 pages · 2,380 words
Page 1
PS-M & PS-MO RANGE PS32, 40, 55 & 65 MARINE MANUAL ARTICULATING WALL MOUNTS INSTALLATION INSTRUCTIONS ISSUE 001
Page 3
SAFETY DISCLAIMER IMPORTANT SAFETY INSTRUCTIONS BELOW WARNING: Failure to provide adequate structural strengthening, prior to installation can result in serious personal injury or damage to the equipment. It is the installer’s responsibility to ensure the structure to which the component is affixed can support four times the weight of the component and any additional apparatus mounted to the component. WARNING: Do not exceed the weight capacity for this product as listed below. This can result in serious personal injury or damage to the equipment. It is the installer’s responsibility to ensure that the total combined weight of all attached components does not exceed that of the maximum figure stated. WARNING: Risk of death or serious injury may occur when children climb on audio and/or video equipment or furniture. A remote control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over on to the child. WARNING: Risk of death or serious injury may occur. Relocating audio and/or video equipment to furniture not specifically designed to support audio and/or video equipment may result in death or serious injury due to the furnishing collapsing or over turning onto a child or adult. WARNING – RISK OF INJURY! Only for use with equipment weighing 132LBS (60KG) OR LESS. Use with heavier projectors/equipment may lead to instability causing tip over or failure resulting in death or serious injury. Bracket Suitable for Residential and Commercial Use. ADDITIONAL WARNINGS: 1. Keep all documentation/instructions after fitting. 2. Read all technical instructions fully before installation and use. It is the installer’s responsibility to ensure that all documentation is passed on to the end user and read fully before operation. 3. Do not use near water or outdoors unless the product has been specifically designed to do so. 4. Protect any cables or cords being used near this bracket from being walked on or pinched to prevent damage and risk of injury. 5. Use this product only for its intended purpose as described in the product instructions and only use attachments/ accessories specified by the manufacturer. 6. Do not operate the product if it is damaged in any way, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Contact the original installer/manufacturer to arrange repair or return. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons: 1. Clean only with a dry cloth and always unplug any electrical items being used in conjunction with this product before cleaning. Future Sound & Vision trading as Future Automation intend to make this and all documentation as accurate as possible. However, Future Automation makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without prior notice or obligation of any kind. Future Automation makes no representation of warranty, expressed or implied, regarding the information contained herein. Future Automation assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. 1
Page 4
PRODUCT WARRANTY & RISK ASSESSMENT WARRANTY INFORMATION WARNING - The warranty offered for this product shall be annulled if the product is used improperly or in a way that is in breach of our Terms of Service. Future Automation provides warranty for the mechanism you purchased for the period of 24 months from the date of purchase, provided that it isn’t used for unintended purposes. Under the warranty, Future Automation aims to either solve the issue remotely (via telephone or email support) or if the mechanism requires a part, arrange a visit to your premises by a Future Automation approved engineer or send replacement items where appropriate. Warranty repairs will be carried out as quickly as possible, but subject to parts availability. This warranty period is respectively extended for the period of a repair. A malfunctioning product must be cleaned and placed into suitable packaging to protect against transit damage before organising delivery to a repair workshop. All the complaints about defects must be submitted to the vendor/installer that sold this product, rather than directly to the manufacturer. Any part of your system that needs to be replaced during a warranty repair becomes the property of Future Automation. The warranty does not cover the following: • Damages resulting from improper product use or maintenance. • Repairs carried out by unauthorized persons. • Natural wear and tear during operation. • Damages caused by the buyer. • Accidental damages caused by a customer or damages caused as a result of careless attitude or usage, or damages caused by natural disasters (natural phenomena). • Any electrical, or other environmental work external to your Future Automation mechanism including power cuts, surges etc. • Additional items not supplied by Future Automation although they may have been supplied together by the retailer • Any 3rd party software products controlling your mechanism • Any transfer of ownership. Warranty is provided only to the initial purchaser. • Compensation for loss of use of the product, and consequential loss of any kind. A separate Safety and Servicing Information document is provided with these instructions (additional copies can be found at www.futureautomation.co.uk/safety), and this document MUST be filled out by the approved Future Automation Dealer who is installing the product. This Warranty Sheet must be held by the end user for the duration of the products life and will be referred to during servicing or warranty queries. The Safety and Servicing Information document also contains two Service History Forms that must be filled in by the approved Future Automation dealer who is performing the first required yearly service of this product. One copy of the Service History Form must be held by the customer (along with the Warranty Sheet) and a duplicate copy must be held by the approved Future Automation dealer that performed the service. Missing and/or mismatching documents may delay or invalidate warranty claims. Additional Service History Forms can be found on the Future Automation website for further yearly services. RISK ASSESSMENT INFORMATION It is the installer’s responsibility to perform a risk assessment of installed products. Future Automation can provide guidelines to installers/dealer about what should be included in a risk assessment, but due to the individual nuances of each location/site, Future Automation cannot provide a full list of areas to risk assess. For full risk assessment and safety information please view our Safety and Servicing guide available at www.futureautomation.net/safety 2
Page 5
GUIDE CONTENTS SAFETY DISCLAIMER 1 PRODUCT WARRANTY & RISK ASSESSMENT 2 GUIDE CONTENTS 3 PACKAGE CONTENTS 4 VESA MOUNT ADJUSTMENTS 5 MOUNTING HEIGHT CALCULATION 9 SCREEN MOUNT DETACHMENT 10 SURFACE MOUNTING 12 CABLE MANAGEMENT 14 FITTING THE SCREEN 15 FRICTION ADJUSTMENT 17 MARINE CATCH ADJUSTMENT 18 SCREEN LEVEL ADJUSTMENT 19 3
Page 6
PACKAGE CONTENTS 1 - PS-M RANGE BRACKET 1.1 - TOP BEAM 1.2 - SCREEN MOUNT UPRIGHTS 1.3 - CATCH SPACERS (X4) 1.4 - WALL PLATE 1.5 - TOP WALL BEAM 1.6 - BOTTOM WALL BEAM ITEMS NOT SHOWN ON PAGE PS-M RANGE ACCESSORY PACK: - SCREEN FIXINGS PACK (MULTI-PACK OF NUTS, BOLTS, SPACERS AND WASHERS) - PACK OF CABLE TIES 1.5 1.6 1.1 1.4 1.2 1.3 4
Page 7
VESA MOUNT ADJUSTMENTS VESA 100/ 200 The PS-M brackets will arrive with the mount head in VESA 100 / 200 configuration shown to the left. For 1 VESA patterns 300 to 400, follow steps 2 to 8 to re- configure the PS bracket, otherwise skip to page 9. A B 100.40 mm VESA 100 200.40 mm VESA 200 Remove the two M6 fixings on the bottom of 2 the screen frame as shown on the right. 4 mm 5
Page 8
VESA MOUNT ADJUSTMENTS CONT. 3 Pull the bottom edge of the screen frame away from the bracket. Screen frame 4 Lift and unhook the screen frame from the PS bracket. 6
Page 9
VESA MOUNT ADJUSTMENTS CONT. Pz2 Remove the two pozi head bolts 5 at the top of the screen frame. Slide bobbin 6 10 mm Remove the four hex bolts and slide bobbins*. * When reattaching the uprights ensure they are at the correct distance apart before tightening the hex bolts. 7
Page 10
VESA MOUNT ADJUSTMENTS CONT. Top cross beam 7 Slide out the top and bottom cross beams. A B Bottom cross beam Upright 8 B A Swap the uprights over. Follow steps 5 to 7 in reverse order to reattach all parts. 8
Page 11
MOUNTING HEIGHT CALCULATION Dimension X Place the PS Bracket on the back of the screen and line up the screen's VESA holes with the corresponding slots on the screen mount. Measure from the top of the screen, down to the top mounting hole on the wall plate (Dimension X as indicated above) to determine positioning of the top wall fixing holes. 9
Page 12
SCREEN MOUNT DETACHMENT 4 mm 1 Remove the two M6 fixings on the bottom of the screen frame as shown on the right. 2 Pull the bottom edge of the screen frame away from the PS bracket. 10
Page 13
SCREEN MOUNT DETACHMENT CONT. 3 Lift the screen frame off of the PS bracket. Top beam Catch spacer 4 Fix the top beam and catch spacers onto the screen frame. 4 mm 11
Page 14
SURFACE MOUNTING 4 mm Top wall beam Wall plate 1 Fix the top and bottom wall beams to the wall plate. Ensure to use the supplied catch spacers for the bottom wall beam. Catch spacer Bottom wall beam 12
Page 15
SURFACE MOUNTING CONT. 2 3 The top fixing hole for the PS Bracket wall Fix through the top Ø8.5mm [5/16”] fixing plate should be located the distance of hole in the wall plate to secure it to the Dimension X (measured on page 9) down wall. Once checking the bracket is level from the top of the screen position. For on the wall, secure the bracket using the ease of access, the scissor arms can be remaining 7 fixing holes using suitable pulled out and fixed in place by inserting a fixings (NOT SUPPLIED) as indicated below. screwdriver (or similar) into the side of the wall plate as shown below. NOTE: Maximum fixing bolt head size = 18mm [11/16”] Scissor arms Use a screwdriver or similar to hold the scissor arms open. 13
Page 16
CABLE MANAGEMENT Power and signal cable wall sockets should be kept outside of the footprint of the bracket to 1 maximise space available for cable routing - see Tech/ CAD files for bracket dimensions. All cables should enter the bracket at the top of the wall plate, run down each of the outer scissor arms and attach to the rear of the screen frame as shown below. Use supplied 2 cable ties to secure all cables to the cable anchors on the scissor arms and tie bridges on the screen uprights. 3 Ensure sufÏcient slack is left at the top pivot point of the bracket. Ensure sufÏcient slack is left where the cables span between the scissor arm and the screen frame. Fully advance and rotate the bracket in both directions to ensure cables do not restrict 4 movement. Ensure sufÏcient cable slack here. Scissor arms Ensure sufÏcient cable slack here. 14
Page 17
FITTING THE SCREEN Lay the screen face down on a padded surface and place the screen mount onto the screens four mount holes. Secure the screen mount to the back of the screen, using the bolts and washers provided in the fixings pack as shown below. If the screen has recessed mount holes 1 or if you need to space the screen mount uprights off for clearance, use the spacers provided in the fixings pack. If the screen being installed has a very low set VESA pattern then an optional Vertical Offset Adapter can be used to extend the effective length of the screen mount. Lay each adapter plate 2 onto the front face of the screen mount and secure in place using 4 x M8 nuts provided. 3 If the screen mount uprights need to be re-configured to suit an alternative VESA pattern, see page 5. Top of screen Optional Vertical Offset Adapters NOTE: Screens that do not have standard VESA bolt patterns may require an adapter plate. 15
Page 18
FITTING THE SCREEN CONT. 4 Hook the screen and screen mount onto the PS bracket. Make sure the 2 locator nubbins at the top of the screen mount are securely fixed onto the plate at the top of the bar. 4 mm 5 Secure the screen and screen mount to the rest of the bracket by replacing the 2 x M6 bolts into the underside of screen mount. 6 Connect all power and signal cables to the screen and check that enough slack has been left for the full range of motion of the bracket. 16
Page 19
FRICTION ADJUSTMENT Bottom sliding collar 4 mm M5 bolt Once fitted, if you find that the PS bracket's pull function is too stiff or too loose, the friction can be adjusted using the M5 nut and bolt arrangement on the bottom sliding collar as shown above. Loosen the bolt to decrease friction, or tighten to increase friction. 17
Page 20
MARINE CATCH ADJUSTMENT 4 mm Loosen the four M6 marine catch fixings 1 to adjust the position of the marine catches. Retighten once adjusted. Cord Push the PS bracket in. An audible ‘click’ will 2 indicate when the marine locks are engaged. Pull the cords to disengage the locks. CLICK! 18
Page 21
SCREEN LEVEL ADJUSTMENT Pz2 Located on the top face of the top beam, two pozi head bolts can accessed through slots. Adjust these bolts to alter the screen frame rotation. Use a spirit level to check. 19
Page 22
EUROPEAN OFFICE NORTH AMERICAN OFFICE Address: Address: Unit 6-8 Enterprise Park Brunel Road 127 Venture Drive Bedford Dover Bedfordshire NH MK41 9TG 03820 Phone: +44 (0) 1438 833577 Phone: +1 (603) 742 9181 Email: info@futureautomation.co.uk Email: info@futureautomation.net OfÏce Hours: OfÏce Hours: Mon - Fri 8:00 to 17:30 GMT Mon - Fri 7:00 to 17:00 EST Saturday & Sunday - Closed Saturday & Sunday - Closed www.FUTUREAUTOMATION.net
Need assistance or looking to source this item?