This document could not be shown here. Open the PDF.
Text of this document9 pages · 895 words
Page 1
EAD ELECTRIC ADVANCE & DROP BRACKET TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 015 WWW NET . . SHEET 1 FUTUREAUTOMATION
Page 2
EAD ELECTRIC ADVANCE & DROP BRACKET SPECIFICATION MEASUREMENTS Screen Sizes (Approx) 50"-80" Maximum Weight Capacity 50Kg (110lb) Depth From Wall 138mm (5 7/16") Maximum Extension From Wall 550mm (21 5/8") Maximum Drop from In Position 533mm (21") Packaging Dimensions 840 x 750 x 270mm (33 1/16" x 29 1/2" x 10 5/8") Shipping Weight 25Kg (55lb) Movement Type Motorised Power Supply Required 110V - 240V AC Power Consumption Max. 120W Power Consumption Standby 3W Mounting Patterns Supported VESA 600, 500, 400, 300, 200 W x 500, 400, 300, 200 H Control Options IR Remote, RS232, Contact Closure Product Options / Features Specific B&O and Loewe mounts / adapters, Custom RAL paint finishes Package Contents Mechanism, IR remote control, Control box Marine Suitable No TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 015 WWW NET . . SHEET 2 FUTUREAUTOMATION
Page 3
EAD ELECTRIC ADVANCE & DROP BRACKET CABLE ROUTING The EAD's mounting allows for cables from the screen to be fed through the integrated cable management. This allows P the cables to be stowed tidily within the mechanism. Screen and Mechanism cables should be routed to a control box behind the wall via an opening in the back of the wall or a conduit leading to it. Use cable ties to NOTE: TURN THE MECHANISM OFF FROM THE MAINS WHEN keep cables tidy. ROUTING CABLES. THE EAD HAS A VERY POWERFUL MOTOR AND NO ANTI JAM FEATURE AVAILABLE! Use cable clamps to retain cable, leave a loop in the 8 1/8" screen cables to prevent DETAIL A 5 7/8" 207 cable strain. 149.5 2 1/16" 52 Cable Exit To Mains Power A Mechanism cable exits Possible cable exit. through a cable gland, P from here wires can be directed through the hole in the wall plate. Cable tie cables to outside of sheet metal here to prevent rubbing. TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 015 WWW NET . . SHEET 3 FUTUREAUTOMATION
Page 4
EAD ELECTRIC ADVANCE & DROP BRACKET 5 7/16" POSITIONING AND MOVEMENT DETAILS 138 The EAD can clear a 305mm [12"] mantle piece with ease when mounted 70mm [2 3/4"] above it. A screen with height of 690mm [27 3/16"] will be required to cover the mechanism The graph below gives an approximation of wall plate height position assuming the bottom edge of the screen is flush with the wall plate. Black Line = Wall mounted Red Line = Recessed in WB-EAD 21" 533 MAXIMUM DROP 2 3/4" 70 17 11/16" RADIUS OF TRAVEL 17 11/16" R450 449 6" 152 If the EAD is being recessed then the figure for mantle piece depth increases by the recess depth value. If the lower screen edge is not flush with the EAD wall plate, the wall plate height above mantle increases by 4 3/16" the offset amount. 107 Due to mechanical tolerances between moving components, mechanisms may experience a level deviation of up to +/- 0.15deg between the in and out positions. TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 015 WWW NET . . SHEET 4 FUTUREAUTOMATION
Page 5
EAD ELECTRIC ADVANCE & DROP BRACKET SCREEN MOUNTING Remove screen mount as shown below and assemble to screen. BOLT MOUNT TO SCREEN Reassemble screen mount to mechanism in reverse of disassembly. Route cables as shown. TILT AND UNHOOK MOUNT PLATE REMOVE M6 BOLTSREMOVE M6 BOLTS HOOK ON AND RE-INSERT M6 BOLTS TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 015 WWW NET . . SHEET 5 FUTUREAUTOMATION
Page 6
EAD ELECTRIC ADVANCE & DROP BRACKET C POSITION ADJUSTMENT The EAD can be adjusted to fine tune the up and down positions. Refer to instructions for more information on switch adjustment. Away from wall Toward wall Out Position Adjuster B Decrease drop DETAIL B In Position Adjuster Loosen bolts and slide in slots to adjust Increase drop DETAIL C TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 015 WWW NET . . SHEET 6 FUTUREAUTOMATION
Page 7
EAD ELECTRIC ADVANCE & DROP BRACKET UP POSITION DIMENSIONS Upright allows 22 7/16" for 3 of tilt 570 18 15/16" 482 24 7/16" 22 1/8" 621 563 27 3/16" 691 8 1/4" 210 23 5/8" 12" 600 305 5 7/16" 138 TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 015 WWW NET . . SHEET 7 FUTUREAUTOMATION
Page 8
EAD ELECTRIC ADVANCE & DROP BRACKET DOWN POSITION DIMENSIONS 21 5/8" 550 2 1/16" 53 8 1/4" 210 Note: Any object, whether placed 27" intentionally or accidentally within this 686 area, may be damaged or cause damage to the mechanism. 18 7/16" 469 TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 015 WWW NET . . SHEET 8 FUTUREAUTOMATION
Page 9
EAD ELECTRIC ADVANCE & DROP BRACKET WALL PLATE DIMENSIONS 11 13/16" 300 3/16" 5 C L SYM 7 1/16" 180 5 5/8" 143 8 1/4" C L 210 2 11/16" 68 1 3/16" 30 0" 0 5/16" 6 5/16" 8 160 8 1/4" 210 10 1/4" 260 TECHNICAL SHEET UK +44 (0) 1438 833577 US +1 (603) 742 9181 ISSUE 015 WWW NET . . SHEET 9 FUTUREAUTOMATION
Need assistance or looking to source this item?