Lutron RadioRA 3 2-column Keypad (RRE-WSS-2, RR-WS-2) Installation Guide (P/N 044428 Rev A, 11/2025)

Page 1

Troubleshooting Turn OFF power at circuit breaker or remove fuse Installing the button kit to the construction cover 1 5 Symptom Cause Action WARNING: SHOCK HAZARD. Snap the construction cover onto the button kit. Status LEDs on Power not present Circuit breaker OFF or fuse May result in serious injury or death. Always isolate the mains power supply or remove the keypad don’t at keypad is faulty. Turn ON breaker or Standard Keypad 044428 Rev A The button kit is sold separately from the light up when replace fuse 11/2025 fuse before servicing or installing. RRE-WSS-2 keypad. If you do not have a button buttons on it are Please read before installing. English kit, reinstall the construction cover until you have pressed Incorrect wiring Check the wiring against a button kit. Step 2 of the instructions. RR-WS-2 The dimmer, switch or Refer to the RadioRA 3 RRE-WSS-2 shade / drapery is not programming software 220 – 240 V~ 50 / 60 Hz 1 mA W iring assigned to the keypad and ensure the device is 2 assigned to the keypad. Included Components Perform a transfer and Bulk Keypad Connect the wires using the diagram. A specific make sure it is successful. Mounting Plate dimmer, switch or Failure has occurred on Replace the lamp(s). N = Neutral shade / drapery the lamp(s) controlled Button Kit L = Live is not controlled * Breaker by the dimmer/switch Construction Cover = Earth Installing the construction cover to the keypad when a button is 6 pressed on the There is no power to Ensure that the device is Mounting Screws keypad the dimmer, switch, powered. shade/drapery *RR-WS-2 only Snap the construction cover onto the keypad, engaging the top two snaps first and then the Devices are out of Ensure the device is placed bottom two. range within 6 m of two additional Replace the construction cover with the wallplate compatible wireless 0,6 N•m after construction has been completed. devices. L The button was not Refer to the RadioRA 3 Note: Wallplate installation instructions are programmed correctly programming software N included with the wallplate. Dimmer, switch and ensure the device is or shade / drapery assigned to the keypad. does not go to Perform a transfer and RR-WS-2 shown above the desired level make sure it is successful. or position when Note: RRE-WSS-2 will not have a a button on the Devices are out of Ensure the device is placed button kit on the bulk unit. keypad is pressed range within 6 m of two additional 5 mm Turn ON power at circuit breaker or install fuse compatible wireless 7 devices. Products must be installed in accordance with the latest All status LEDs on The keypad is in the Refer to the RadioRA 3 Help building and wiring regulations. the keypad flash Factory Settings mode programming software Note: Terminals are designed for one wire per terminal only. when any button and has not been and ensure the device is is pressed configured to work in assigned to that keypad. RA3 Support Center a system Perform a transfer and Removing the construction cover make sure it is successful. For additional support with 3 The LEDs on the The 2-column keypad Check the system installing, programming, and Construction cover with Construction cover Pry off the construction cover using a right column of a was activated in a configuration to confirm troubleshooting System setup 2-column keypad location which was that the keypad is currently a button kit: without a button kit: screwdriver or similar tool. The construction 8 are not lit, but the defined in the system as defined as a 1-column cover will be reinstalled in step 6. If a button LED briefly turns a 1-column keypad keypad. If it is, deactivate kit is already installed before this step, it This keypad must be used in a RadioRA 3 system with a processor for control of dimmers, switches, on for about 3 the device in the system, should stay installed in the construction cover and shades. seconds when remove the 1-column during removal. Use the RadioRA 3 programming software to setup the system (training is required to access the software). the corresponding keypad from the system, Note: Do not attempt to program a keypad if it does not have a button kit installed. button is pressed and then add it again as a new 2-column keypad. lutron.com/RA3support IMPORTANT Note: Refer to the system’s Setup Guide for additional troubleshooting suggestions. Europe: 0800.282.107 or +44.(0)20.7702.0657 1. Install in accordance with all national and local electrical codes. RR-WS-2 shown above RRE-WSS-2 shown above 2. For indoor use only between 0 °C and 40 °C; 0% – 90% humidity, non-condensing. www.lutron.com/support Mounting Return to Factory Settings Limited Warranty: 4 www.lutron.com/warranty or call 1.844.LUTRON1 (USA/Canada) Note: Returning a keypad to its factory settings will remove the keypad from the system and erase or +1.610.282.3800 (Others) for a printed copy. Depth: 35 mm minimum all programming. Note: On a 2-column keypad, the below steps must be performed on the left column. Hereby, Lutron Electronics Co., Inc. declares that the radio equipment Step 1: Triple tap the top button on the keypad. DO NOT release after third tap. type RR-WS-2 and RRE-WSS-2 are in compliance with Directive Step 2: Keep the button pressed on the third tap until all the status LEDs start to flash slowly 2014/53/EU M3.5 mm x (approximately 3 seconds). The full text of the EU declaration of conformity is available at the 30 mm Step 3: Immediately release the button and triple tap the button again. The status LEDs on the following internet address: lutron.com/cedoc keypad will flash quickly. The keypad has now been returned to its factory settings. Lutron, RadioRA 3, and any related trade dress and logos are trademarks or registered trademarks of Lutron Electronics Co., Inc. in 3 sec the US and/or other countries. All other product names, logos, and brands are property of their Mount the keypad to the backbox using the After the keypad is mounted, go to step 5 to respective owners. horizontally located screw holes only as shown. add the button kit. The vertical mounting holes are not compatible If the button kit was already installed with the ©2025 Lutron Electronics Co., Inc. with a square backbox. Do not use them. construction cover, go to step 6.