Lutron RadioRA 3 Keypad (RRE-WSS-1, RR-WS) Installation Guide (printed P/N 044423 Rev A, 03/2025)

Page 1

Turn OFF power at circuit breaker or remove fuse Removing the Construction Cover IMPORTANT 1 4 1. Install in accordance with all national and local electrical codes. WARNING: SHOCK HAZARD. If the keypad already has a button kit installed (RR-WS), 2. For indoor use only between 0 °C and 40 °C; 0% – 90% humidity, Standard Keypad 044423 Rev A May result in serious injury or death. Always isolate the mains power supply or skip to step 7. non-condensing. 03/2025 remove fuse before servicing or installing. Please read before installing. English If the keypad does not have a button kit installed RRE-WSS-1 (RRE-WSS-1), follow the instructions below to install the Return to Factory Settings button kit (button kit is sold separately). RR-WS Note: Returning a keypad to its factory settings will remove the 220 – 240 V~ 50 / 60 Hz 1 mA Use a screwdriver or other tool to pry free the corners of the construction cover and remove the construction keypad from the system and erase all programming. Included Components cover from the keypad. Step 1: Triple tap the top button on the keypad. DO NOT release Bulk Keypad after third tap. 1 W iring Adding the Button Kit Step 2: Keep the button pressed on the third tap until all the status Mounting Plate 2 5 LEDs start to flash slowly (approximately 3 seconds). 2 Button Kit Step 3: Immediately release the button and triple tap the button Construction Cover Connect the wires using the diagram. N = Neutral Snap the construction cover onto the button kit. again. The status LEDs on the keypad will flash quickly. Mounting Screws Breaker L = Live The keypad has now been returned to its factory settings. 1 When Included = Earth 2 For RR-WS only 3 sec Help 0,6 N•m RA3 Support Center For additional support with L installing, programming, N and troubleshooting Troubleshooting 5 mm A dding the Construction Cover to the Keypad Symptom Cause Action lutron.com/RA3support 6 Status LEDs Power not present Circuit breaker OFF or fuse Europe: +44.(0)20.7702.0657 Products must be installed in accordance with on the keypad at keypad is faulty. Turn ON breaker or the latest building and wiring regulations. Snap the construction cover onto the keypad, engaging don’t light up replace fuse Indonesia: 001.803.011.3994 the top two snaps first and then the bottom two. when buttons Incorrect wiring Check the wiring against KSA: 140.025.05512 Note: Terminals are designed for one wire per on it are Step 2 of the instructions terminal only. Replace the construction cover with the wallplate after pressed. Singapore: 800.120.4491 construction has been completed. The dimmer, switch or Refer to the RadioRA 3 Thailand: 001.800.120.665853 Note: Wallplate installation instructions are included shade / drapery is not programming software UAE: +800.031.10102 Mounting with the wallplate. assigned to the keypad and ensure the device is 3 assigned to the keypad. India: 000800.050.1992 A specific Perform a transfer and U.S.A. / Canada: 1.844.LUTRON1 dimmer, make sure it is successful switch or Failure has occurred on Replace the lamp(s) Mexico: +1.888.235.2910 Depth: 35 mm minimum shade / drapery is not controlled the lamp(s) controlled by Other Countries (toll): +971600521581 when a button the dimmer/switch is pressed on There is no power to the Ensure that the device i the keypad. dimmer, switch, s powered Turn ON power at circuit breaker or install fuse shade/drapery 7 www.lutron.com/support M3.5 mm x Devices are out of range Ensure the device is placed 30 mm within 6 m of two additional Limited Warranty: compatible wireless devices https://assets.lutron.com/a/documents/intl_warranty.pdf Dimmer, The button was not Refer to the RadioRA 3 switch or programmed correctly programming software shade / drapery and ensure the device is Mount the keypad to the backbox Wallplate installation instructions are does not go assigned to the keypad. using the horizontally located screw included with the wallplate. Replace to the desired Perform a transfer and Hereby, Lutron Electronics Co., Inc. declares that the radio equipment holes only as shown. construction cover with wallplate after level or position make sure it is successful type RRE-WSS-1 and RR-WS are in compliance with Directive when a button 2014/53/EU construction has been completed. on the keypad Devices are out of range Ensure the device is placed The full text of the EU declaration of conformity is available at the is pressed. within 6 m of two additional following internet address: lutron.com/cedoc compatible wireless devices Lutron, RadioRA 3, and any related trade dress and logos are System setup trademarks or registered trademarks of Lutron Electronics Co., Inc. in the 8 All status LEDs The keypad is in the Refer to the RadioRA 3 US and/or other countries. on the keypad Factory Settings mode programming software All other product names, logos, and brands are property of their This keypad must be used in a RadioRA 3 system with a processor for control of dimmers, switches, flash when and has not been and ensure the device is respective owners. any button is configured to work in assigned to that keypad. and shades. pressed. a system Perform a transfer and Use the RadioRA 3 programming software to setup the system (training is required to access the software). make sure it is successful ©2025 Lutron Electronics Co., Inc. Do not attempt to program a keypad if the keypad does not have a button kit installed. Note: Refer to the system setup guide for additional troubleshooting suggestions.