This document could not be shown here. Open the PDF.
Text of this document8 pages · 1,293 words
Page 1
Wireless Processor Installation Instructions RRKE-PROC3 Please Read Before Installing 48 V- 100 mA English Product Overview P/N 044411 Rev. A 12/2024 Status LED Green = Normal operation Blue = Firmware upgrade in process Red = Error Yellow = No Internet connection/access Program Button Used to factory reset processor and to associate into a system This RadioRA 3 wireless processor works with compatible wireless devices, including standard and hybrid keypads, Pico controls, Radio Powr Savr sensors, RF dimmer and switch modules, plug-in dimmers, and Triathlon, Sivoia QS wireless and Palladiom wire free shades. Other products may also be compatible; see individual product spec sheets for details on system compatibility. This wireless processor must be powered by an IEEE 802.3af, IEEE 802.3at or IEEE 802.3bt compliant LPS / SELV PoE or PoE+ power supply.
Page 2
Additional Components Note: Mounting adapter must be purchased separately. Available mounting adapters are: L-SMNT-WH shelf-mount, L-CMNT-WH recess-mount, and L-JMNT-WH junction box mount Included in RRKE-PROC3-KIT1 PoE injector and 1 m 1.8 m region-specific plugs Ethernet cable Ethernet cable P/N: L-POEI-G-BL Included in RRKE-PROC3-CW Components Recess-mount Junction box (not included) adapter mount adapter Plaster ring P/N: L-CMNT-WH P/N: L-JMNT-WH 70 mm Tools You May Need Ladder Hole saw Drill Philips head screwdriver Pencil 83 mm to 89 mm 4.5 mm drill bit 2
Page 3
Step 1 — Choose a Location to Install Reliability of Clear Connect wireless communication requires that the wireless processor be centrally-located and within a maximum distance of the specific wireless devices in the system. Wireless processors must be mounted 2 m away from wireless interference sources like microwaves, Wireless Access Points (WAPs), etc. PoE wiring must be kept internal to the building. Do not run PoE wiring outdoors or install the processor in metallic enclosures. Distances for Wireless Devices Clear Connect – Type A Devices (in-line RF dimming and switching modules and plug-in lamp dimmers, Pico wireless controls, Sivoia QS wireless shades, etc.) • Each device must be within 9 m of a r epeater or wireless processor. • Repeaters can be spanned up to 18 m apart fr om other repeaters to create the network. Clear Connect – Type X Devices • All devices associated with the wireless processor must be within a 23 m radius of the processor. • There must be a minimum of two devices within 6 m of the wireless processor. • Each Clear Connect – Type X device should have two or more non-battery powered Type X devices within 6 m of another compatible Clear Connect – Type X device. Using more than two devices is ideal for creating an ultra high-performance mesh network. Groups or clusters of Clear Connect – Type X devices must not be separated by more than 6 m. For more information, please refer to the Wireless Setup Guide which can be found in the RA3 Support Center: www.lutron.com/RA3support For myLutron users, please see Application Note 842 for additional information on Clear Connect - Type X Best Practices at www.lutron.com/europe 3
Page 4
Select the Mounting Adapter for your Installation Step 2 — RRKE-PROC3-CW comes with a recess-mount adapter and a junction box mount adapter. For model RRKE-PROC3-KIT1, the mounting adapters are sold separately. Available mounting adapters are: L-SMNT-WH shelf-mount, L-CMNT-WH recess-mount, and L-JMNT-WH junction box mount Step 3 — Provide Opening for Adapter (recess-mount and junction box mount adapter ONLY) 83 mm to 89 mm 8 mm to 30 mm Step 4a — Installation using the Recess-Mount Adapter Ceiling installation Wall installation Wall Ceiling OR Recess-mount Recess-mount adapter adapter Plug in Ethernet cable and attach processor to PoE-enabled network switch or PoE injector Recess-mount adapter RJ45 Connector (Ethernet Jack) 4
Page 5
Step 4b — Installation using the Junction Box Mount Adapter Ceiling installation Wall installation Junction box Mud ring OR Junction box Junction box Junction box mount adapter mount adapter Plug in Ethernet cable and attach processor to PoE-enabled network switch or PoE injector Junction box Junction box mount adapter RJ45 Connector (Ethernet jack) 5
Page 6
Step 4c — Installation using the Shelf-Mount Adapter (P/N: L-SMNT-WH, sold separately) • Hold the adapter to the wall in Horizontal Vertical the desired location • Using a pencil, mark the location of the screw holes • If using drywall, prep for anchors Level • Partially drive two (2) screws at Surface least 6.3 mm into the wall or the M3 screw Wall drywall anchors recommended • Feed right-angle connector (2 included) of the 1.8 m Ethernet cable through the adapter BEFORE tightening screws • Tighten screws • Plug in Ether net cable and attach processor to PoE-enabled network switch or PoE injector • Attach processor to adapter PoE injector or switch Wireless processor WiFi router IN OUT Internet 6
Page 7
Step 5 — System Setup For more information, please refer to the Getting Started Guide, which can be found in the RA3 Support Center: www.lutron.com/RA3support LED Diagnostics Mode / Error LED Pattern Description Normal Operation Status LED blinks green every 10 seconds Software Update Status LED blinks blue Error Status LED remains solid red Processor Identify Status LED blinks green rapidly Processor has no Internet access Status LED blinks yellow every 5 seconds Troubleshooting Symptom Probable Cause Unit does not A PoE switch is not being used or is not configured as a PoE switch power on The other end of the Ethernet cable is not connected to a PoE switch Unit cannot be The Ethernet cable is not connected to the same LAN as the wired processor found in software Model is not supported (Athena / myRoom vs. HomeWorks) Ethernet run is longer than the supported 100 m and a PoE extender is needed Unit does not Lights are out of range of the wireless processor control Processor lost power / Ethernet wire run too long and PoE booster is required surrounding lights LED on unit is Processor does not have Internet connectivity. Verify that the processor is blinking yellow connected to a network configured for internet access. Wait for up to 1 minute every 5 seconds after implementing any corrective actions. Refer to the Application note #760 (048760) at www.lutron.com/europe for network troubleshooting details LED on unit is Contact Lutron Tech Support only if maintained more than 30 seconds or if it solid red occurs periodically. For additional troubleshooting information, please see www.lutron.com/RA3support 7
Page 8
Hereby, Lutron Electronics Co. Inc declares that the radio equipment type RRKE-PROC3 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.lutron.com/cedoc Controlling this HomeKit®-enabled accessory automatically and away from home requires a HomePod®, Apple® TV, or iPad® set up as a home hub. It is recommended that you update to the latest software and operating system. Communication between iPhone®, iPad®, Apple Watch®, HomePod®, or Mac® and the HomeKit®- enabled RadioRA 3 processor is secured by HomeKit® technology. Use of the Works with Apple® badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been certified by the developer to meet Apple® performance standards. Apple® is not responsible for the operation of this device or its compliance with safety and regulatory standards. The Lutron logo, Lutron, Athena, Clear Connect, HomeWorks, myRoom, Palladiom, Pico, RadioRA 3, Radio Powr Savr, Sivoia QS, and Triathlon and are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries. Apple, Apple Watch, HomeKit, HomePod. iPad, iPhone, and Mac are trademarks of Apple Inc., registered in the U.S. and other countries. All other product names, logos, and brands are property of their respective owners. ©2024 Lutron Electronics Co., Inc. Customer Assistance Limited Warranty For questions concerning the installation For warranty information, please or operation of this product, please visit scan the code below with a www.lutron.com/RA3support smartphone. 8
Need assistance or looking to source this item?