Future Automation LSL-BE installation instructions

Page 1

Installation Instructions L i LSL BE - Lift System Light Box Enclosure f t

M e c Design Highlights h a -Quiet Smooth Lifting Action at Approximately 40mm [1.6”] per Second n i s -Full Cable Management m -Wide Range of Mounting Options s -24V DC Motor. Suitable for Direct DC Supply -Marine Suitable Robust Beam Thank you for choosing futureautomation email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565 ISSUE 002

Page 2

LSL BE - Lift System Light Box Enclosure n o i t Caution a Safety Disclaimer Beware of Danger Keep Hands m Important Safety Instructions Warning Moving Parts Electricity Clear r o Explanation of graphical symbols f n -(Electric Shock Symbol) = The lightning flash within an equilateral triangle is intended to alert you to the presence of un-insulated I

y “dangerous voltage” within the products enclosure that may be of sufficient magnitude to constitute an electric shock to persons t e -(Caution Symbol) = The exclamation point within an equilateral triangle is intended to alert you to the presence of important f a operating and maintenance (servicing) instructions in the literature accompanying the product S -(Tools Symbols) = The tools symbol within a coloured square are intended to highlight the required tools necessary for correct and

: safe installation of the product. These are intended as a n o guide only, and it is at the installer’s discretion as to which tools are used. i t c u WARNING:RISK OF ELECTRIC SHOCK, ONLY AUTHORIZED INSTALLERS TO OPEN THE POWER CONTROL BOX. d WARNING:To reduce the risk of fire or electric shock, do not expose electrical parts to rain or moisture, unless the o r product has been specifically designed to do so. t n WARNING:Failure to provide adequate structural strengthening, prior to installation can result in serious personal injury or damage to the I equipment. It is the installer’s responsibility to ensure the structure to which the component is affixed can support the four times the weight of the component. WARNING:Do not exceed the weight capacity. This can result in serious personal injury or damage to the equipment. It is the installer’s responsibility to ensure that the total combined weight of all attached components does not exceed that of the maximum figure stated. WARNING:Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equip- ment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. Warnings: 1. Read all technical instructions fully before installation and use. It is the installer’s responsibility to ensure that all documentation is passed on the end user and read fully before operation. 2. Keep all documentation. 3. Heed all warnings. 4. Follow all technical specifications and instructions during installation. 5. Do not use near water unless the product has been specifically designed to do so. 6. Clean only with a dry cloth. 7. Do not defeat the purpose of the polarized or grounding type plug. A polarized plug has two blades, one wider than the other. A grounding type plug has two blades and a grounding prong. The wide blade or third prong are provided for your safety. If the provided plug does not fit your outlet, consult an electrician or contact the manufacturer. 8. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where the exit from the apparatus. 9. Unplug the apparatus during lightning storms or when unused for long periods of time. 10. Only use attachments/accessories specified by the manufacturer. 11. Refer all servicing to qualified personnel. Servicing is required regularly on an annual basis, when the apparatus is damaged in any way, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 12. To completely disconnect the apparatus form the AC mains, disconnect the power cord plug from the AC receptacle on the power control box. 13. To prevent overheating, do not cover the apparatus. Install in accordance with the instructions. 14. UK, Ireland and Hong Kong only – The power cord is supplied with a 13A plug having an earthing pin. The apparatus is earthed and this pin is not required for safety, merely to operate the safety shutter of mains outlet. 15. No naked flames such as lit candles should be placed on the unit. 16. Observe and follow the local regulations when disposing of batteries. 17. Do not expose the unit to dripping or splashing fluids. 18. Do not place objects filled with liquid, such as vases, on the unit. 19. Do not expose the batteries to excessive heat such as sunshine, fire or the like. 20. For all mounted apparatus, the apparatus should be installed on solid wood, bricks, concrete or solid wood columns and battens. 21. Always turn off power at source before putting on or taking off parts and cleaning. 22. Do not use outdoors unless marked for outdoor use. 23. Exceeding the weight capacity can result in serious personal injury or damage to equipment. Future Sound & Vision trading as Future Automation intend to make this and all documentation as accurate as possible. However, Future Automation makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without prior notice or obligation of any kind. Future Automation makes no representation of warranty, expressed or implied, regarding the information contained herein. Future Automation assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. Page 1 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 3

LSL BE - Lift System Light Box Enclosure Contents Page I n t r Introduction o d Safety Information 1 u c t Contents 2 i o Contents 3 n :

Tool Indicator Icons 3 C o n t e Installation n t Parts List s Package Contents 4 Stage 1 Before You Start 5 Remove KH Screen Mount 5 Stage 2 Fixing the Lift in the Cabinet 6 Stage 3 KH Upright Assembly 7 Stage 4 Mounting the Box Enclosure 8 Stage 5 Attaching the Enclosure 9 Stage 6 Routing the Cables & Screen Mount Plate Fixings 10 Stage 7 Screen & Box Enclosure Mounting 11 Stage 8 Switch Adjustments 12 Electrical Connections Contact Closure 13 RS232 Controls 14 IR Controls 15 Operations IR Control & Operation 15 Storing Positions 15 Changing Batteries 15 Trouble Shooting 16 Technical Overview 17 Notes 18 Page 2 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 4

LSL BE - Lift System Light Box Enclosure r Contents Page o t a c i d n I

: n o i t c u d o r t n I Tool Indicator Icons 1. 2. 3. 4. 5. 6. 7. 8. 1. - Drill 3. - Allen Keys 5. - Screwdrivers 7. - Pencil 2. - Tape measure 4. - Spirit Level 6. - Spanners 8. - Saw Product Warranty This product carries a warranty that covers the cost of labour and spare parts incurred by any defects in materials and workmanship under normal use during a two year period from date of purchase. Support for any problems that are not hardware faults are excluded from the warranty entitlement. This warranty does not affect your statutory consumer rights. The following is excluded from warranty service: • Malfunctioning caused by misuse or damage, accidental or otherwise, or service modification by persons not authorised by Future Automation, or the use of any non Future Automation supplied parts; • Any electrical, or other environmental work external to your Future Automation mechanism including power cuts, surges or lightning strikes; • Additional items not supplied by Future Automation although they may have been supplied together by the retailer; • Any 3rd party software products controlling your mechanism; • Any transfer of ownership. Warranty is provided only to the initial purchaser; • Compensation for loss of use of the product, and consequential loss of any kind; • Use of the product over the specified weight capacity; • Any damage to products during transit that is not checked and notified as “unchecked” or “damaged” upon receipt of delivery. Any part of your system that needs to be replaced during a warranty repair becomes the property of Future Automation. Page 3 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 5

LSL BE - Lift System Light Box Enclosure Package Contents Nuts & Bolts Multipack: I n 1 - Mechanism A range of nuts, bolts, washers s t and spacers to help add in the a 1.1 - Back Plate l l mounting for your screen a 1.2 - Lifting Drive t i o 1.3 - Base Panel Brackets n :

1.4 - KH Lifting Plate P a 1.5 - Screen Mount r t s 1.6 - Cable Management L i 1.7 - Lid Mount Bracket s 1.8 - Adjustable IN/OUT Switch t 2 - Control Box 1 3 - Remote Control Not Shown On Page 1.8 4 - x2 AAA Batteries 1.7 5 - Multi Pack Of Nuts, 1.1 Bolts & Washers 6 - Mains Power & Other Leads 1.7 1.5 3 1.3 1.6 1.8 1.4 2 1.2 1.3 Page 4 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 6

LSL BE - Lift System Light Box Enclosure

e g a t S Before You Start : n o i t Check the Operation of the Mechanism. a l l Firstly, remove all the red cable ties which keep the mechanism safe and secure during a t s transit. n I Once they have all been removed, the mechanism can be powered up and tested. Connect the supplied IR lead and check that the mechanism operates correctly before continuing with the installation. Remove KH Screen Mount Un-lock the KH mount plate but turning the locking lever 90 dgrees and lift off the hook toggles. LID MOUNT BRACKET KH HOOK TOGGLES KH LOCKING LEVER KH MOUNT PLATE Page 5 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 7

LSL BE - Lift System Light Box Enclosure I n s t a l l a Fixing the Lift in the Cabinet t i o n : Place the mechanism within the cabinet. Fix the lift where possible down the back face. S t Make sure that the lifting plate is central by using the centre line marks on the back of a g the back face. e

CENTRE MARKS Page 6 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 8

LSL BE - Lift System Light Box Enclosure

e g a t S KH Upright Assembly

: n o Below shows the KH UPRIGHT assembly. To release the SCREEN MOUNT PLATE rotate i t a the top LOCKING LEVER and lift off the TOGGLES. The TOGGLES can adjust the height by l l a moving up or down the KH UPRIGHT. The ENCLOSURE MOUNT BRACKETS fix to the side t s of the KH UPRIGHT and slide up and down to support the enclosure lid. n I LOCKING LEVER SCREEN MOUNT PLATE ENCLOSURE MOUNT BRACKET TOGGLES KH UPRIGHT Page 7 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 9

LSL BE - Lift System Light Box Enclosure I n s t a l l Mounting the Box Enclosure a t i o n After the mechanism is in the correct position the next step is to lower the BOX :

ENCLOSURE into place and fix from the underside through the BASE PANEL S t a BRACKETS. A good tip is to place the BOX ENCLOSURE in place and draw g e

marks from the underside through the BASE PANEL BRACKETS, then fix using a 4 wood screw and a large penny washer, this will allow you to adjust the position. BOX ENCLOSURE ENCLOSURE LID BRACKETS BASE ENCLOSURE BASE PANEL BRACKETS Page 12 Stage 8 - Details on adjusting the OUT position Page 8 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 10

LSL BE - Lift System Light Box Enclosure

e g a t Attaching the Enclosure S

: n With the mechanism still in the UP position fix the base panel to the BASE PANEL o i t BRACKETS, adjust the height so the base panel sits flush to the cabinet top. Then a l l adjust the ENCLOSURE LID BRACKETS to the correct height to support the cabinet a t s lid and enclosure. n I ENCLOSURE LID FIXING ENCLOSURE BASE FIXING Page 9 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 11

LSL BE - Lift System Light Box Enclosure I n s t a l l Routing Cables & Screen Mount Plate Fixing a t i o n Once the ENCLOSURE is fixed to :

S the mechanism thread the screen t a g and power cables through the e

cable management chain and 6 then through the lifting beam shown with the orange dotted line. KH MOUNT UPRIGHT SCREEN Hook the SCREEN MOUNT MOUNT PLATE on to the KH UPRIGHT PLATE over the TOGGLES and secure using the LOCKING LEVER. Page 10 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 12

LSL BE - Lift System Light Box Enclosure 7

e g a t Screen & Box Enclosure Mounting S

: n o Slide the screen into the i t a enclosure and fix to the l l a SCREEN MOUNT PLATE. t s A good tip is to use a n I packer under the screen and remove once fixed and secure. Finally offer the box enclosure back panel and fix to the sides. This back panel needs to be removable to take the screen off. Page 11 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 13

LSL BE - Lift System Light Box Enclosure I n s t a l l Switch Adjustments a t i o n You can adjust the IN and OUT position of the lifting beam. Detail 1 shows how :

S to adjust the OUT position and detail 2 shows how to adjust the IN position. t a g The IR sensor can be located anywhere outside of the cabinet. e

8 1- The top switch can’t be adjusted when the mechanism is in the OUT position, because the switch is active. Lower the mechanism and press STOP after about 100mm [4”]. Then adjust the OUT switch plate by loosening the bolts and sliding the plate. 1 2 2- Bottom switch can be adjusted by repeating the first procedure. Page 12 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 14

LSL BE - Lift System Light Box Enclosure n SLQV o i t c e Contact Closure n n o C

l - Use an RJ45 connector in the CCI a c socket on the control box to operate i r t c via contact closure e l E

: n o i t a l l a t s n WIRE / CABLE CONTACT CLOSURE I PIN DESCRIPTION ACTION 568A 568B LED INDICATOR 1 12V SUPPLY 12V SUPPLY - CURRENT LIMITED W/G W/O 2 12V LATCH When 12V attached, device will go OUT. When GO 12V removed, device will go IN. 3GROUND GROUND W/OW/G 4 PIN 4 NOT USED BL BL 5 DEVICE LATCH Short to GROUND (pin 3), device will go OUT, W/BL W/BL LED 4 remove short device will go IN. 6 DEVICE STOP Momentary short to GROUND (pin 3), stops O G LED 3 device in current position. 7 DEVICE OUT Momentary short to GROUND (pin 3), makes W/BR W/BR LED 2 device go OUT. 8 DEVICE IN Momentary short to GROUND (pin 3), makes BR BR LED 1 device go IN. LED 1 LED 2 LED 3 LED 4 LED 5 NOTE: CONTACT CLOSURE INPUT Earlier versions of the control board may not have these contact closure LED indicators. Page 13 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 15

LSL BE - Lift System Light Box Enclosure I n s t a l l RS232 a t i - Use an RJ25 connector o n in the socket marked :

R RS232 on the control box S 2 to operate using RS232 3 2

C o n t r o Pin 1: RX l Pin 6 : TX SLQV Pin 2: TX Pin 3 & 4: GROUND Pin 3: RX Pin 5: GROUND Details Baud rate: 9600 RJ25 9 PIN D Stop bit: 1 Parity: None PIN 1: RX TO PIN 2: TX Databits: 8 PIN 6: TX TO PIN 3: RX PIN 3: GROUND TO PIN 5: GROUND IMPORTANT PIN 4: GROUND TO PIN 5: GROUND Ensure protocol is entered exactly as written, including Carriage Return (Enter / ASCII 13). Protocol Action fa_in Carriage Return (Enter ) Device IN fa_out Carriage Return (Enter ) Device OUT fa_stop Carriage Return (Enter ) Device STOP (At any position) Connection Locations Mains Voltage Input RS232 Contact Closure IR LED Emergency Stop Connector IR Input Jack Page 14 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 16

LSL BE - Lift System Light Box Enclosure l o r t n o Operation buttons for the IR remote C

: n o i In - Brings the mechanism Out- Brings the t a l inside the cabinet mechanism out of the l a t cabinet facing forward s n I Stop- Will stop the operation at any position Note Only buttons indicated are functional with the product. Any button pressed when in motion will stop the mechanism. Replacing batteries Future Automation IR RemoteController needs x2 AAA batteries which are provided within the packaging Page 15 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 17

LSL BE - Lift System Light Box Enclosure T r o u b l Lift System Light Box Enclosure - Trouble shooting guide e

S h o o t i n Lift System Light Box Enclosure - Trouble shooting g For information on our products please refer to our web site - : www.futureautomation.co.uk or for questions on installations and our product range please phone us on - +44(0) 1438 833577 and ask for our technical support department Page 16 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 18

LSL BE - Lift System Light Box Enclosure : w e i v r e Technical Overview v O

l A general technical overview of the LSL BE lift mechanism range a c i n h c e ] ] 2 ] , T " " ] " e 3 5 3 6 6 t 2 . . . . o S m ] 5 0 4 ] 3 R m ] " ] 1 3 [ 2 m V m 4 [ [ b W ] ] [ " . b l 0 b b e & 0 ) m 0 0 9 l 3 m 9 l l R 1 V 2 . 0 3 9 m m . 0 A 5 5 k m e 1 2 5 2 0 x . E m 1 5 5 3 c m F r s x x 2 m m 7 m [ [ R u r 1 1 8 B 4 - a 9 e ( 0 3 x . 5 4 9 1 [ 0 l , s o . 1 [ L 9 6 1 0 g g B 9 e o Y s 1 8 0 1 S 3 7 g W 1 K K 5 t l V e 2 x 0 x g L - K 0 C 0 x K - - 5 6 - o Y 9 3 6 h 9 5 2 1 t 4 0 . x . 4 h t t 1 2 t m c 2 5 5 0 3 2 t h p h e a 1 [ 0 2 d g e g t [ i i i R 6 e D e n R o W H H I C ] ] 2 ] " " , 3 " ] 6 e 5 3 6 . t 2 . . . o S m ] E 5 7 4 ] 0 R m ] " ] 1 2 [ 2 m V m 4 [ [ b W ] ] [ " . b G l 0 b b e & 0 ) m 0 0 9 l N 2 m 5 l l R 1 V 2 . 0 3 5 m m . 0 A 5 5 k m e 1 2 5 2 0 x . A E m 7 5 5 3 c m F r s x x 8 R m m 7 m [ [ R u r 1 1 8 B 3 - a 4 e ( 0 3 x . 4 4 4 1 [ 0 l , s o . 1 [ E L 9 9 1 0 g g B 2 e o Y s 1 8 0 1 B S 3 6 g W 1 K K 5 t l V e 2 x 0 x g L - K 0 C 0 x K L - - 5 6 - o Y 9 3 6 h 7 5 2 1 t 4 0 . x . 2 S h t t 1 2 t m c 2 5 5 0 3 2 L t h p h e a 1 [ 0 2 d g e g t [ i i i R 6 e D e n R o W H H I C ] ] 2 ] " " , 3 " ] 1 e 5 8 6 . t 2 . . . o S m ] 5 2 4 ] 6 R m ] " ] 1 2 [ 1 m V m 4 [ [ b W ] ] [ " . b l 0 b b e & 0 ) m 0 0 9 l 1 m 0 l l R 1 V 2 . 0 3 1 m m . 0 A 5 5 k m e 1 2 5 2 0 x . E m 3 5 5 3 c m F r s x x 4 m m 7 m [ [ R u r 1 1 8 B 3 - a 0 e ( 0 3 x . 4 4 0 1 [ 0 l , s o . 1 [ L 9 8 1 0 g g B 1 e o Y s 1 8 0 1 S 3 5 g W 1 K K 4 t l V e 2 x 0 x g L - K 0 C 0 x K - - 5 6 - o Y 9 3 6 h 5 5 2 1 t 4 0 . x . 0 h t t 1 2 t m c 2 5 5 0 3 2 t h p h e a 1 [ 0 2 d g e g t [ i i i R 6 e D e n R o W H H I C ) x

e n r t D x n P , h i u y s n n r o y l o g a e t p W r i e n o o r ( p e i i M z p g o t t i p n i M S a u W s p p n P S e s A a x y y z l R n m m t t e n d r i i s e o i i e o y r e S a e r u u c c r i l 3 t n m p s s y a a c s p w x e o z i n n S i f i i p b p p v p o o D s S D o o d a a e u O B A d l P g n t t C C n C C r l S l l e c c t a r e t n u u h r r a g g T o r o u o i e e t d u r e r r p m d d g S n n t t p t i i i i n o x t p o o e w w n t t a l a n w n u n i D r r o o f f t o o o o o h i i P P W P P O L L S C M C P C O C S Page 17 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 19

LSL BE - Lift System Light Box Enclosure Notes... Page 18 of 18 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565

Page 20

Future Automation Unit 2 Kimpton Enterprise Park Claggy Road Kimpton Hertfordshire SG4 8HP United Kingdom Tel: +44 (0) 1438 833 577 Fax: +44 (0) 1438 833 565 Email: info@futureautomation.co.uk www.futureautomation.co.uk