This document could not be shown here. Open the PDF.
Text of this document27 pages · 5,889 words
Page 1
Lutron seeTouch QS Wallstations 369489k 1 04.02.26 Color and Engraving Codes LED QSWS2-1BN-___-___ QSWS2-1BI-___-___ 1-Button Wallstation Description • Offers toggle functionality for any combination of zone(s) in the system. • Receives up to two contact closure inputs through a connector on the back of the wallstation. • Large, rounded buttons are easy to use. • Backlit buttons with optional engraving make it easy to find and operate the wallstation in low-light conditions. • Optional button engraving is angled up to the eye for easy reading. • The LEDs next to each button are used during QSWS2-1BN-WH programming and provide feedback when the buttons (Non-insert version) are pressed. QSWS2-1BI-WH (Insert version) 1 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 2
Lutron seeTouch QS Wallstations 369489k 2 04.02.26 Color and Engraving Codes (continued) LEDs QSWS2-2BN-___-___ QSWS2-2BI-___-___ 2-Button Wallstation Description • Often used in entryways to select Scene 1 1 and Off. Off • Receives up to two contact closure inputs through a connector on the back of the wallstation. • Large, rounded buttons are easy to use. Engraving • Backlit buttons with optional engraving make it easy to find and operate the wallstation in low-light conditions. • Optional button engraving is angled up to the eye for QSWS2-2BN-WH-EGN easy reading. (Non-insert version) • The LEDs next to each button are used during programming and provide feedback when the buttons are pressed. QSWS2-2BI-WH (Insert version) 2 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 3
Lutron seeTouch QS Wallstations 369489k 3 04.02.26 Color and Engraving Codes (continued) LEDs QSWS2-3BN-___-___ QSWS2-3BI-___-___ 3-Button Wallstation Description 1 • Often used to select scenes. 2 • Receives up to two contact closure inputs through a 3 connector on the back of the wallstation. • Large, rounded buttons are easy to use. • Backlit buttons with optional engraving make it easy to find and operate the wallstation in low-light Engraving conditions. • Optional button engraving is angled up to the eye for easy reading. QSWS2-3BN-WH-EGN • The LEDs next to each button are used during (Non-insert version) programming and provide feedback when the buttons are pressed. QSWS2-3BI-WH (Insert version) 3 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 4
Lutron seeTouch QS Wallstations 369489k 4 04.02.26 Color and Engraving Codes (continued) LEDs QSWS2-5BN-___-___ QSWS2-5BI-___-___ 5-Button Wallstation Description • Often used to select between 4 scenes and Off. • Receives up to two contact closure inputs through a connector on the back of the wallstation. • Large, rounded buttons are easy to use. • Backlit buttons with optional engraving make it easy to find and operate the wallstation in low-light conditions. • Optional button engraving is angled up to the eye for easy reading. QSWS2-5BN-WH • The LEDs next to each button are used during (Non-insert version) programming and provide feedback when the buttons are pressed. 1 2 3 4 Off Engraving QSWS2-5BI-WH-EGN (Insert version) 4 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 5
Lutron seeTouch QS Wallstations 369489k 5 04.02.26 Color and Engraving Codes (continued) LEDs QSWS2-7BN-___-___ QSWS2-7BI-___-___ 7-Button Wallstation 1 Description 2 • Often used to select scenes. 3 • Receives up to two contact closure inputs through a 4 connector on the back of the wallstation. 5 • Large, rounded buttons are easy to use. 6 • Backlit buttons with optional engraving make it 7 easy to find and operate the wallstation in low-light Engraving conditions. • Optional button engraving is angled up to the eye for easy reading. QSWS2-7BN-WH-EGN • The LEDs next to each button are used during (Non-insert version) programming and provide feedback when the buttons are pressed. QSWS2-7BI-WH (Insert version) 5 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 6
Lutron seeTouch QS Wallstations 369489k 6 04.02.26 Color and Engraving Codes (continued) LED QSWS2-2BRLN-___-___ QSWS2-2BRLI-___-___ 2-Button Wallstation with Raise / Lower Description • Often used to select and adjust scenes. 1 Scene Off Selection • Receives up to two contact closure inputs through a Buttons connector on the back of the wallstation. • Large, rounded buttons are easy to use. • Backlit buttons with optional engraving make it Engraving easy to find and operate the wallstation in low-light Master Raise / Lower conditions. • Optional button engraving is angled up to the eye for easy reading. QSWS2-2BRLN-WH-EGN • Master Raise / Lower brightens or dims all lighting or (Non-insert version) raises / lowers all assigned shades in the last selected scene or toggled group. • The LEDs next to each button are used during programming and provide feedback when the buttons are pressed. • S hade control features (E01 engraving): – Can control Sivoia QS window treatments. – Pressing the Open (or Close) button once will cause the window treatments to move to their fully open Open (or closed) position. Tap any button (regardless of Close function) to stop a shade that is in motion. QSWS2-2BRLI-WH-E01 (Insert version) 6 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 7
Lutron seeTouch QS Wallstations 369489k 7 04.02.26 Color and Engraving Codes (continued) LED QSWS2-3BRLN-___-___ QSWS2-3BRLI-___-___ 3-Button Wallstation with Raise / Lower Description Open • Often used to select and adjust scenes. Preset • Receives up to two contact closure inputs through a Close connector on the back of the wallstation. • Large, rounded buttons are easy to use. • Backlit buttons with optional engraving make it easy to Engraving find and operate the wallstation in low-light conditions. • Optional button engraving is angled up to the eye for easy reading. • Master Raise / Lower brightens or dims all lighting or Master Raise / Lower raises / lowers all assigned shades in the last selected QSWS2-3BRLN-WH-E01 scene or toggled group. (Non-insert version) • The LEDs next to each button are used during programming and provide feedback when the buttons are pressed. • Shade control features (E01 engraving): – C an control Sivoia QS window treatments. – P ressing the Open (or Close) button once will cause the window treatments to move to their fully open 1 (or closed) position. Tap any button (regardless of 2 function) to stop a shade that is in motion. 3 – One (1) programmable preset button. QSWS2-3BRLI-WH-EGN (Insert version) 7 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 8
Lutron seeTouch QS Wallstations 369489k 8 04.02.26 Color and Engraving Codes (continued) LED QSWS2-5BRLN-___-___ QSWS2-5BRLI-___-___ 5-Button Wallstation with Raise / Lower 1 Description 2 • Often used to select and adjust scenes. 3 Scene • Receives up to two contact closure inputs through a 4 Selection Buttons connector on the back of the wallstation. Off • Large, rounded buttons are easy to use. • Backlit buttons with optional engraving make it easy to find and operate the wallstation in low-light conditions. Engraving • Optional button engraving is angled up to the eye for easy reading. Master Raise / Lower • Master Raise / Lower brightens or dims all lighting or QSWS2-5BRLN-WH-EGN raises / lowers all assigned shades in the last selected (Non-insert version) scene or toggled group. • The LEDs next to each button are used during programming and provide feedback when the buttons are pressed. • S hade control features (E01 engraving): – Can control Sivoia QS window treatments. Open – Pressing the Open (or Close) button once will cause Preset 1 the window treatments to move to their fully open Preset 2 (or closed) position. Tap any button (regardless of Preset 3 function) to stop a shade that is in motion. Close – Three (3) programmable preset buttons. QSWS2-5BRLI-WH-E01 (Insert version) 8 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 9
Lutron seeTouch QS Wallstations 369489k 9 04.02.26 Color and Engraving Codes (continued) LED QSWS2-2BRLIRN-___-___ QSWS2-2BRLIRI-___-___ 2-Button Wallstation with Infrared (IR) Receiver and Raise / Lower Description 1 Scene Selection • Often used to select and adjust scenes. Off Buttons • Receives up to two contact closure inputs through a connector on the back of the wallstation. Engraving • Large, rounded buttons are easy to use. IR Window • Backlit buttons with optional engraving make it easy to find and operate the wallstation in low-light conditions. • Optional button engraving is angled up to the eye for Master Raise / Lower easy reading. QSWS2-2BRLIRN-WH-EGN • Master Raise / Lower brightens or dims all lighting or (Non-insert version) raises / lowers all assigned shades in the last selected scene or toggled group. • The LEDs next to each button are used during programming and provide feedback when the buttons are pressed. • S hade control features (E01 engraving): – Can control Sivoia QS window treatments. – Pressing the Open (or Close) button once will cause the window treatments to move to their fully open (or closed) position. Tap any button (regardless of function) to stop a shade that is in motion. QSWS2-2BRLIRI-WH (Insert version) 9 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 10
Lutron seeTouch QS Wallstations 369489k 10 04.02.26 Color and Engraving Codes (continued) LED QSWS2-3BRLIRN-___-___ QSWS2-3BRLIRI-___-___ 3-Button Wallstation with Infrared Receiver and Raise / Lower 1 Description 2 • Often used to select and adjust scenes. 3 • Receives up to two contact closure inputs through a connector on the back of the wallstation. • Large, rounded buttons are easy to use. Engraving • Backlit buttons with optional engraving make it IR Window easy to find and operate the wallstation in low-light conditions. • Optional button engraving is angled up to the eye for Master Raise / Lower easy reading. QSWS2-3BRLIRN-WH-EGN • Master Raise / Lower brightens or dims all lighting or (Non-insert version) raises / lowers all assigned shades in the last selected scene or toggled group. • The LEDs next to each button are used during programming and provide feedback when the buttons are pressed. • S hade control features E01 engraving): – Can control Sivoia QS window treatments. Open – Pressing the Open (or Close) button once will cause Preset the window treatments to move to their fully open Close (or closed) position. Tap any button (regardless of function) to stop a shade that is in motion. – One (1) programmable preset button. QSWS2-3BRLIRI-WH-E01 (Insert version) 10 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 11
Lutron seeTouch QS Wallstations 369489k 11 04.02.26 Color and Engraving Codes (continued) LED QSWS2-5BRLIRN-___-___ QSWS2-5BRLIRI-___-___ 5-Button Wallstation with 1 Infrared Receiver and Raise / Lower 2 Description 3 Scene 4 Selection • Often used to select and adjust scenes. Buttons • Receives up to two contact closure inputs through a Off connector on the back of the wallstation. • Large, rounded buttons are easy to use. Engraving • Backlit buttons with optional engraving make it easy to find and operate the wallstation in low-light IR Window conditions. • Optional button engraving is angled up to the eye for Master Raise / Lower easy reading. QSWS2-5BRLIRN-WH-EGN (Non-insert version) • Master Raise / Lower brightens or dims all lighting or raises / lowers all assigned shades in the last selected scene or toggled group. • The LEDs next to each button are used during programming and provide feedback when the buttons are pressed. • S hade control features (E01 engraving): – Can control Sivoia QS window treatments. – Pressing the Open (or Close) button once will cause the window treatments to move to their fully open (or closed) position. Tap any button (regardless of function) to stop a shade that is in motion. – Three (3) programmable preset buttons. QSWS2-5BRLIRI-WH (Insert version) 11 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 12
Lutron seeTouch QS Wallstations 369489k 12 04.02.26 Color and Engraving Codes (continued) LED QSWS2-1RLDN-___-___ QSWS2-1RLDI-___-___ Dual Wallstation with 3-Button and 2-Button with Raise / Lower Group 1 Group 2 Description Group 3 • Used to control one or more lighting or window treatment groups simultaneously. Open Engraving • Functions as two independently programmable Close controllers: a 3-button (top keypad group) and a 2-button (bottom keypad group). Can control two lighting zones, Raise / Lower two shade zones, or one of each. • Receives up to two contact closure inputs through a connector on the back of the wallstation. QSWS2-1RLDN-WH-E01 • Large, rounded buttons are easy to use. (Non-insert version) • Backlit buttons with on-button engraving make it easy to find and operate the wallstation in low-light conditions. • Optional button engraving is angled up to the eye for easy reading. • The LEDs next to each button are used during programming and provide feedback when the buttons are pressed. 1 • S hade control features (E01 engraving): 2 – Used to control multiple groups of shades 3 independently from a single-gang keypad (e.g., a window with a sheer shade and a blackout shade). Open – Often used to select three different groups of shades Close using Open, Close, and Raise / Lower. – Can control Sivoia QS window treatments. – Pressing the Open (or Close) button once will cause the window treatments to move to their fully open (or closed) position. Tap any button (regardless of function) QSWS2-1RLDI-WH-EGN to stop a shade that is in motion. (Insert version) 12 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 13
Lutron seeTouch QS Wallstations 369489k 13 04.02.26 Color and Engraving Codes (continued) LED QSWS2-2RLDN-___-___ QSWS2-2RLDI-___-___ Dual 2-Button Wallstation with Raise / Lower Open Description Close Engraving • Used to control one or more lighting or window treatment groups simultaneously. Raise / Lower • Functions as two independently programmable Open 2-button controllers. Can control two lighting zones, Close two shade zones, or one of each. • Receives up to two contact closure inputs through a Raise / Lower connector on the back of the wallstation. • Large, rounded buttons are easy to use. • Backlit buttons with on-button engraving make it easy to find and operate the wallstation in low-light QSWS2-2RLDN-WH-E01 conditions. (Non-insert version) • Optional button engraving is angled up to the eye for easy reading. • The LEDs next to each button are used during programming and provide feedback when the buttons are pressed. • S hade control features (E01 engraving): 1 – Can be used to control multiple groups of shades 2 independently from a single-gang keypad (e.g., a window with a sheer shade and a blackout shade). – Can control Sivoia QS window treatments. Open – Pressing the Open (or Close) button once will cause Close the window treatments to move to their fully open (or closed) position. Tap any button (regardless of function) to stop a shade that is in motion. QSWS2-2RLDI-WH-EGN (Insert version) 13 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 14
Lutron seeTouch QS Wallstations 369489k 14 04.02.26 Color and Engraving Codes (continued) LED QSWS2-3BDI-___-___ QSWS2-3BDN-___-___ Dual 3-Button Wallstation 1 Description 2 • Used to control one or more lighting or window 3 treatment groups simultaneously. • Functions as two independently programmable Open 3-button controllers. Can control two lighting zones, Preset two shade zones, or one of each. Close • Receives up to two contact closure inputs through a connector on the back of the wallstation. • Large, rounded buttons are easy to use. Engraving • Backlit buttons with on-button engraving make it QSWS2-3BDN-WH-EGN easy to find and operate the wallstation in low-light (Non-insert version) conditions. • Optional button engraving is angled up to the eye for easy reading. • The LEDs next to each button are used during programming and provide feedback when the buttons are pressed. • S hade control features (E01 engraving): Open – Can be used to control multiple groups of shades Preset independently from a single-gang keypad (e.g., a Close window with a sheer shade and a blackout shade). – Can control Sivoia QS window treatments. Open – Pressing the Open (or Close) button once will cause Preset the window treatments to move to their fully open Close (or closed) position. Tap any button (regardless of function) to stop a shade that is in motion. – One (1) programmable preset button per 3-button column. QSWS2-3BDI-WH-E01 (Insert version) 14 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 15
Lutron seeTouch QS Wallstations 369489k 15 04.02.26 Specifications Dimensions Power Input (Control Link Terminal 2) Front View SELV / PELV / NEC® Class 2. Operating voltage: 24–36 V- 30 mA Key Design Features • Field-changeable button and faceplate assemblies allow easy customization. • Meets IEC 801-2. Tested to withstand 15 kV electrostatic discharge without damage or memory loss. • Faceplate snaps on with no visible means of attachment. • Available as an “insert” style control for multiganging. • Can be ganged to share a common faceplate with Nova T* and Vareo dimmers. To order new wallplates for multi-ganging, specify “R3” openings in a Nova T* multi-gang FB (fins broken) series model number. • Use Faceplate Replacement Kits to change color, button configuration, or engraving, or to convert between non-insert and insert configurations. System Communications and Capacity 22 in (70 mm) • SELV / PELV / NEC® Class 2 wiring connects wallstations to other devices on the QS Link. Side View • A QS system can have up to 100 devices and 100 zones; seeTouch QS wallstations each count as one device and zero zones on the QS Link. 18 in • A seeTouch QS wallstation consumes one power draw unit (PDU) on the (30.2 mm) QS link. For complete information, see Power Draw Units on the QS Link (P/N 369405) at www.lutron.com Terminals 2 Accept up to two 18 AWG (1.0 mm ). Environment • 32 °F to 104 °F (0 °C to 40 °C). Relative humidity less than 90% 4# in non-condensing. (116 mm) • For indoor use only. Compatibility seeTouch QS keypads are compatible with GRAFIK Eye QS, Sivoia QS, Energi Savr Node, and Quantum systems. Mounting 5/16 in Typical backbox dimensions: (8 mm) 13/16 in 3.75 in (95 mm) high, (20.6 mm) 2.1875 in (55 mm) wide, 2.75 in (70 mm) deep. Back View QS Link 4 Connector 3 2 !WARNING – Entrapment Hazard – May result in serious injury or death. These controls should 1 only be used to control equipment which is visible from every control location. Sensor / !WARNING – Fire Hazard – May result in serious injury or death. Only use these controls to Contact operate approved load and equipment types. C Closure IMPORTANT NOTE: Examples of such equipment which must not be operated by these controls B Input A Connector include (but are not limited to) motorized gates, garage doors, industrial doors, microwave ovens, heating pads, fireplaces, space heaters, etc. It is the installer’s responsibility to ensure that the equipment being controlled is visible from every control location and that only suitable equipment is connected to these controls. Failure to do so could result in serious injury or death. 15 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 16
Lutron seeTouch QS Wallstations 369489k 16 04.02.26 Available Control Types seeTouch wallstations are available in three types: Lights Only Lights and Shades Shades Only 1 Open 1 2 Preset 1 2 3 Preset 2 3 Preset 3 Open Close Close QSWS2-3BRLI-WH-EGN QSWS2-1RLDI-WH-EGN QSWS2-5BRLI-WH-E01 (Insert version) (Insert version) (Insert version) Lights Only • Controls only lights. • Has a programmable column type (choose from the list on the following pages). • Engraving options: General (EGN) and Non-Standard (NST). Lights and Shades • Top column controls only lights and has a programmable column type (choose from the list on the following pages). • Bottom column controls only shades and has a programmable column type (choose from the list on the following pages). • Engraving options: General (EGN) and Non-Standard (NST). Shades Only • Controls only shades. • Models with preset buttons have programmable preset levels. • Engraving options: Standard (E01), Secondary (E02), and Non-Standard (NST). 16 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 17
Lutron seeTouch QS Wallstations 369489k 17 04.02.26 Available Column Types Scene (with Off) • Controls pre-programmed scenes on one or more scene controllers (such as a GRAFIK Eye QS, or an area on an Energi Savr Node). • Buttons within a column control the same scene controller(s) (different buttons within a column cannot control different scene controllers). • The scene recalled by the first button in a column is programmable, subsequent buttons recall the next numerical scene, and the last button always recalls Scene Off. • A 1-button scene wallstation will always toggle between the assigned scene and Scene Off. Scene (without OFF) • Identical function to scene with Off, except the last button in a column recalls the next consecutive scene, not Scene Off. Zone Toggle • Buttons toggle a zone or group of zones between programmable preset values and Off (where all zones are Off). • Each zone can be programmed to a different value. • Each button can be individually programmed to a different zone or group of zones. Partition • Allows the user to assign individual buttons of a column to different scene controllers (areas). • One button press (button LED lights) indicates an open partition within the space so that devices programmed to that button talk to each other in both directions. • A second button press (button LED goes off) indicates a closed partition within the space so that devices programmed to that button function independently. 2B Partition (2-button wallstation only) • Identical function to partition, except that there are two buttons. • A top button press indicates an open partition; a bottom button press indicates a closed partition. 2B Fine Tune (2-button wallstation only) • Buttons function as raise and lower buttons for assigned zones. • A button tap will raise / lower the level of assigned zones by 1 percent. • Pressing and holding the buttons smoothly raises to high end or smoothly lowers to low end. 2B Sequence (2-button wallstation only) • All assigned scene controllers continuously cycle through either Scenes 1-4 or Scenes 5-16 using the programmed fade times for each scene. • Useful for spaces that desire dynamic lighting, such as decorative lighting or displays in retail stores. (continued on next page) 17 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 18
Lutron seeTouch QS Wallstations 369489k 18 04.02.26 Available Column Types (continued) 2B Panic (2-button wallstation only) • Button press causes all assigned scene controllers go to Scene 16. • Temporarily disables all button presses and ignores scene or zone level changes. 2B Timeclock (2-button wallstation only) • Allows the user to enable or disable the timeclock on a GRAFIK Eye QS. • A top button press enables the timeclock; a bottom button press disables the timeclock. Shade • Wallstation must have more than 1 button. • Raise / Lower buttons are recommended for programming. • The top button becomes the Open button; the bottom button becomes the Close button for associated Lutron Sivoia QS shades or third-party AC shades. • For keypads with more than two buttons, the middle buttons are programmable preset buttons. Shade Group • Available only on a multi-column keypad where another column is a shade column. • Allows the shade column to operate as multiple independent keypads (one per group). • The shade group column selects which independent keypad is currently active (indicated by the group button whose LED is lit). Note: Column types can be changed using the GRAFIK Eye QS programming menu (e.g., control programmed as lights only can be changed to shades only). 18 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 19
Lutron seeTouch QS Wallstations 369489k 19 04.02.26 How to Build a Standard seeTouch QS Model Number QSWS2- -WH- Button Configurations Prefix Button Insert White Engraving Configuration Style Matte Code* (see next page) Finish 2B 3B 5B 7B N: Non-insert Generic I: Insert Engraving Code: G for all configurations NOTE: Standard engraving text does not automatically assign or On 1 1 1 re-assign system programming to the QS keypad buttons. Project-specific Off 2 2 2 customer input and programming by a Lutron service team member is still Off 3 3 required to achieve a desired sequence of operation / system functionality 4 per control. 4 * Engraving options may vary based on Button Configuration selected. Off 5 Refer to next pages for available options (see Standard seeTouch QS 6 Wallstation Button Functions Summary). Off Shades Engraving Code: S for all configurations Open Open Open Open Close Preset 1 Preset 1 Preset 1 Close Preset 2 Preset 2 Preset 3 Preset 3 Close Preset 4 Preset 5 Close Hotel Room Engraving Code: H for all configurations DND High High Welcome MUR Low Medium Foyer Off Low Living Nightlight Bed Off Bath Bedside Off Auditorium Engraving Code: A for all configurations All On All On All On All On All Off Present Present Present All Off Lecture Lecture Exam Exam All Off Perform Cleaning All Off 19 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 20
Lutron seeTouch QS Wallstations 369489k 20 04.02.26 Standard seeTouch QS Wallstation Button Functions Summary (WH Only) Button Configurations Button Configurations 2B 3B 5B 7B 2B 3B 5B 7B Lobby Retail Engraving Codes Engraving Codes A L L L A R L T All On All On All On All On All On All On All On All On All Off Event Morning Morning All Off After Hours Morning Morning All Off Afternoon Afternoon All Off Afternoon Afternoon Evening Evening Evening Evening All Off After Hours All Off After Hours Event Cleaning All Off All Off Restaurant Classroom Engraving Codes Engraving Codes A R R R A A A C All On All On All On All On All On All On All On All On All Off After Hours Breakfast Breakfast All Off Present Present Present All Off Lunch Lunch All Off Lecture Lecture Dinner Dinner Exam Exam All Off After Hours All Off Movie Cleaning Cleaning All Off All Off 20 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 21
Lutron seeTouch QS Wallstations 369489k 21 04.02.26 Standard seeTouch QS Wallstation Button Functions Summary (WH only) (continued) Button Configurations Button Configurations 1B 2B 3B 5B 7B 1RLD 2RLD 3BD Meeting Room Shades – Dual Zone Engraving Codes Engraving Code: D for all configurations A M M M N/A Open N/A N/A All On All On All On All On Close All Off Meeting Meeting Meeting Open All Off A / V A / V Close Cleaning Pendant All Off Perimeter Event All Off Lights and Shades A Ballroom Engraving Code: U for all configurations Engraving Codes On On On A L B B Preset Off Preset N/A All On All On All On All On Off Off All Off Event 1 Event 1 Event 1 Open All Off Event 2 Event 2 Open Close Open Event 3 Event 3 Close Preset All Off Event 4 Close Event 5 All Off Lights Dual Zone Private Office Engraving Code: K for all configurations Engraving Codes N/A On On A P P Off Preset Off N/A All On On On N/A On All Off Dim Dim Off On Off Zone 1 Preset Zone 2 Off Off Zone Toggle Lights and Shades B Engraving Code: Z for all configurations Engraving Code: Q for all configurations N/A N/A On On/Off Zone 1 Zone 1 Zone 1 Zone 1 Preset Zone 2 Zone 2 Zone 2 Zone 2 Off Zone 3 Zone 3 Zone 3 Zone 4 Zone 4 Open Zone 5 Zone 5 Stop Zone 6 Close Zone 7 21 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 22
Lutron seeTouch QS Wallstations 369489k 22 04.02.26 How to Build a Custom seeTouch QS Model Number QSWS2- - - Prefix Button Insert Color/ Engraving Configuration Style Finish Code (see next page) N: Non-insert I: Insert Engraving Codes Omit: Unengraved Color/Finish Codes EGN: General Engraving Architectural Matte Finishes Satin Colors Matte Finishes For “Lights only” and “Lights and Shades” White WH Available with Insert (I) controls Ivory IV style controls only. E01: Standard Engraving Beige BE Snow SW For “Shades only” controls Gray GR Midnight MN E02: Secondary engraving for “Shades only” controls Brown BR Taupe TP NST: Non-Standard Text Engraving Black BL Biscuit BI Please visit the GRAFIK Eye QS website at Almond AL Palladium PD* www.lutron.com/grafikeyeqs for custom Light Almond LA Hot HT* engraving forms Taupe TP *N ote: Some Satin Colors units ship Architectural Metal Finishes with different color buttons. For With black plastic buttons (standard). more information, please visit the Engraving Notes Bright Brass BB seeTouch website at Bright Chrome BC www.lutron.com/seetouch • The engraving option (model number and suffix) Bright Nickel BN * For the latest color offerings please is related to the control type, as shown above in Satin Brass SB see our website: the "How to Build a Standard seeTouch QS Satin Chrome SC http://www.lutron.com/satincolors Model Number" section. Satin Nickel SN • Four engraving options are available: Antique Brass QB 1. EGN: G eneral engraving for ‘Lights Only’ and Antique Bronze QZ ‘Lights and Shades’ controls 2. E01: Standard engraving for ‘Shades Only’ Anodized Aluminum Finishes controls and ‘Lights and Shades’ for With black plastic buttons (standard). model QSWE-10BRLI-WH-E01 only Clear CLA 3. E02: Secondary engraving for ‘Shades Only’ Black BLA controls Brass BRA 4. NST: Non-standard engraving for ‘Lights Only’, ‘Lights and Shades’, or ‘Shades Only’ controls • If no engraving is specified, wallstations will ship with an engraving certificate, with EGN being its default engraving type. If no color is specified, wallstations will ship with white (WH) finish. 22 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 23
Lutron seeTouch QS Wallstations 369489k 23 04.02.26 Custom seeTouch QS Wallstation Button Functions Summary Button Configuration 1B 2B 3B 5B 7B 1RLD 2RLD 3BD EGN (General Engraving) Functionality Scene 1 Scene 1 Scene 1 Scene 1 Scene 1 Scene 1 Scene 1 Scene 1 Off Scene 2 Scene 2 Scene 2 Scene 2 Off Scene 2 Scene 3 Scene 3 Scene 3 Scene 3 Scene 3 Scene 4 Scene 4 Open Off Scene 5 Open Close Open Scene 6 Close Preset Scene 7 Close E01 (Standard Engraving) Functionality N/A Open Open Open N/A Group 1 Open Open Close Preset Preset 1 Group 2 Close Preset Close Preset 2 Group 3 Close Preset 3 Open Close Open Close Open Close Preset Close E02 (Secondary/Shades Only Engraving) Functionality N/A N/A N/A N/A N/A Blackout N/A N/A Sheer Both Open Close Legend: Light Control Shade Control 23 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 24
Lutron seeTouch QS Wallstations 369489k 24 04.02.26 How to Build a seeTouch QS Model Number Button Configurations 1B 2B 3B 5B 7B 1-button 2-button 3-button 5-button 7-button 2BRL 3BRL 5BRL 2BRLIR 3BRLIR 2-button with 3-button with 5-button with 2-button with IR 3-button with IR raise / lower raise / lower raise / lower receiver and receiver and raise / lower raise / lower 5BRLIR 1RLD 2RLD 3BD 5-button with IR Dual with 3-button Dual 2-button with Dual 3-button receiver and and 2-button with raise / lower raise / lower raise / lower 24 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 25
Lutron seeTouch QS Wallstations 369489k 25 04.02.26 Faceplate Information Faceplate Replacement Kits Use faceplate replacement kits to change: colors, button configuration, engraving, between insert and non-insert versions. Each kit includes an adapter, button assembly, and wallplate Non-Insert Kit Non-insert style controls: Faceplate complements a specified button kit. When the faceplate is removed or replaced, the buttons are removed and replaced along with it. Insert Kit Insert style controls: Faceplate is a decorator style with a universal size opening that fits all button kits. This style allows for easy replacements of button kits without changing the faceplate. Model Numbers for Kits Non-Insert Insert QSWS2R-1BN QSWS2R-1BI QSWS2R-2BN QSWS2R-2BI QSWS2R-3BN QSWS2R-3BI QSWS2R-5BN QSWS2R-5BI QSWS2R-7BN QSWS2R-7BI QSWS2R-2BRLN QSWS2R-2BRLI QSWS2R-3BRLN QSWS2R-3BRLI QSWS2R-5BRLN QSWS2R-5BRLI QSWS2R-1RLDN QSWS2R-1RLDI QSWS2R-2RLDN QSWS2R-2RLDI QSWS2R-3BDN QSWS2R-3BDI QSWS2R-2BRLIRN QSWS2R-2BRLIRI QSWS2R-3BRLIRN QSWS2R-3BRLIRI QSWS2R-5BRLIRN QSWS2R-5BRLIRI 25 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 26
Lutron seeTouch QS Wallstations 369489k 26 04.02.26 Wallstation Installation Link Wiring (<500 ft/153 m) Data Link: QS Link Wiring (1) twisted, shielded pair 2 22 AWG (0.5 mm ) • Use SELV / PELV / NEC® Class 2 wiring to connect 3: MUX wallstations to the QS Link. D: drain / shield 4: MUX 2 • Connect two 22 AWG (0.5 mm ) s hielded, twisted 4 pair wires to terminals 3 and 4 of the wallstation’s 3 control link connector. Shielding (drain) of the 2 twisted pair wires must be connected together 1 as shown, but do not connect the shielding to earth / ground or the wallstation and do not allow it (2) 18 AWG 2 to contact the grounded wallbox. (1.0 mm ) C • Connect the appropriate size wires to terminals B 1 and 2 for power, according to your link length A (see table below). (2) 18 AWG 2 • Connect drain / shield as shown. Do not connect to (1.0 mm ) ground (earth) or wallstation. Connect the bare SELV / PELV / NEC® Class 2 Control wiring Back View 2 drain wires and cut off the outside shield. (2) 18 AWG (1.0 mm ) 1: Common Note: Use appropriate wire connecting devices as 2: V+ specified by local codes. Link Wiring (500 ft/153 m to 2000 ft/610 m) Data Link: (1) twisted, shielded pair 2 22 AWG (0.5 mm ) 3: MUX 4: MUX 4 3 2 1 (2) 12 AWG 2 (4.0 mm ) SELV / PELV / NEC® Class 2 Control wiring 2 (2) 18 AWG (1.0 mm ) (2) 12 AWG 1: Common 2 2: V+ (4.0 mm ) QS Link Wire Sizes (check compatibility in your area) QS Link Wiring Length Wire Gauge Lutron Cable Part Number Power (terminals 1 and 2) 2 Less than 500 ft (153 m) 1 pair 18 AWG (1.0 mm ) GRX-CBL-346S (non-plenum) Data (terminals 3 and 4) GRX-PCBL-346S (plenum) 2 1 twisted, shielded pair 22 AWG (0.5 mm ) Power (terminals 1 and 2) 500ft to 2000 ft 2 (153 m to 610 m) 1 pair 12 AWG (4.0 mm ) GRX-CBL-46L (non-plenum) Data (terminals 3 and 4) GRX-PCBL-46L (plenum) 2 1 twisted, shielded pair 22 AWG (0.5 mm ) 26 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Page 27
Lutron seeTouch QS Wallstations 369489k 27 04.02.26 Contact Closure Inputs Specifications Contact Closure Input Wiring • Inputs must be dry contact closure, solid-state, • Use low-voltage SELV / PELV / NEC® Class 2 wiring open collector, or active-low (NPN) / active-high to connect the contact closure inputs to the (PNP) output. wallstation. – Open collector NPN or active-low on-state voltage must be less than 2 V- and sink 3.0 mA – Open collector PNP or active-high on-state voltage must be greater than 12 V- and source 3.0 mA 4 (3) 18 AWG 3 • Wallstation is miswire protected up to 36 V-. 2 (1.0 mm ) 2 • Outputs must stay in the closed or open states 1 for at least 40 msec in order to be recognized by the wallstation. Common C Input 2 B A Input 1 Back View Lutron, GRAFIK Eye, Nova T*, Quantum, Satin Colors, seeTouch, Sivoia, Energi Savr Node, Vareo and any related trade dress and logos are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries. All other product names, logos, and brands are property of their respective owners. 27 ® SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number:
Need assistance or looking to source this item?