Lutron HomeWorks Wired seeTouch Designer Keypads – Installation Guide (043359)

Page 1

English Installation Mounting Diagram Troubleshooting Guide 1. Disconnect power to the keypads by turning OFF all circuit breakers Symptom Possible Causes Wired seeTouch® Designer connected to the HomeWorks QS processor or QS link auxiliary power no communication • Miswire or loose connection at the QS wired link. Keypads supplies. Adapter Wallplate with HomeWorks QS • Keypad has not been programmed or has been Installation Instructions 24 V 30 mA PELV (Class 2: USA) 2. Connect to QS wired link. Keypad Mounting processor programmed incorrectly. Wallplate Screws Please Read Before Installing Typical Power Consumption: 0.6 W Mounting Adapter a. Strip insulation 3/8 in (10 mm). Screws Keypad buttons do • Keypad is miswired. HQWD-W1B HQWD-W6B HQWD-W6BRL b. Unplug keypad link terminal block from the back of the keypad. not work; LEDs do not • Keypad is not powered. HQWD-W2BS HQWD-W7B HQWD-W5BIR track. • Keypad has not been programmed or has been HQWD-W3BS HQWD-W3BSRL HQWD-W1RLD c. Connect wiring to terminal block as shown in the Wiring Diagram. Each programmed incorrectly. HQWD-W4BS HQWD-W4S HQWD-W2RLD 2 HQWD-W5B HQWD-W5BRL HQWD-W3BD terminal will accept one or two 18 AWG (1.0 mm ) wires. LEDs do not turn on. • Miswire or loose connection at the keypad(s) or Use these instructions to install the model numbers listed above. d. Plug the keypad link terminal block back onto the keypad. Be sure to processor on the QS wired link. orient the terminal block correctly. • Keypad has been programmed incorrectly. Important Notes 3. Connect external input closures: Connect up to two low-voltage dry contact Contact closure inputs • Miswire or loose connection at the keypad CCI Codes: Install in accordance with all local and national electrical codes. closures (see Wiring Diagram). do not produce the connector. desired result in the • Keypad has not been programmed or has been Environment: Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C), Wiring Diagram Wallbox system. programmed incorrectly. Replacement 0 to 90% humidity, non-condensing. Indoor use only. Keypad buttons do not • Keypad has not been programmed or has been Keypad Kit Wallplates: Use Lutron 2 function as intended. programmed incorrectly. ® Designer (Claro® or Satin Colors®) wallplates. PELV (Class 2: USA) control wiring: 18 AWG (1.0 mm ) Wallplates are sold separately. Lutron Claro and Satin Colors wallplates snap Wallplate adapter and wallplate 2 purchased separately. Keypad LEDs scroll • A communication issue is preventing the keypad on with no visible means of attachment. Data link: twisted, shielded pair 22 to 18 AWG (0.5 to 1.0 mm ) quickly from bottom to from receiving an ID from the system. Cleaning: To clean, wipe with a clean damp cloth. DO nOT use any chemical 5. Install Replacement Kit (if applicable). top. • There are more than 100 devices on the link. cleaning solutions. 6. Attach Lutron Claro or Satin Colors wallplate adapter and wallplate (see 1 1 Wallboxes: U.S. wallbox, 3 ⁄2 in (89 mm) deep, 2 ⁄4 in (57 mm) deep minimum, Mounting Diagram). Returning Keypads to Factory Settings or low-voltage mounting bracket. a. Install the wallplate adapter onto the front of the keypad(s). : Keypad Wiring A Returning a keypad to its Factory Settings will remove the keypad from the S U

6 b. Tighten keypad mounting screws until wallplate adapter is flush to wall (do 3 30 mA 0 8 system and erase all programming. 1

• The total length of wire on a QS wired link is not to exceed 2000 ft (610 m). , not over-tighten). G R U B Step 1: Triple tap any button on the keypad (except raise / lower). DO nOT V S R E • Up to 100 devices can be connected to the QS wired link. This can include P c. Snap wallplate onto wallplate adapter and verify that buttons are aligned 24 O release after third tap. O seeTouch® keypads along with other devices as defined in the HomeWorks C properly. 1 7 9

2 4 Step 2: Keep the button pressed on the third tap until all the status LEDs start QS software. 9 N C 9 9 A 0 d. If control(s) are misaligned, loosen keypad mounting screws appropriately. to flash slowly (approximately 3 seconds). • Wiring may be in a daisy-chain, star, or T-tap configuration. Common 7. Restore power. 2 Step 3: Immediately release the button and triple tap the button again. The • Control wire must be 1 pair 18 AWG (1.0 mm ) PELV (Class 2: USA) for power Input 2 status LEDs on the keypad will flash quickly. 2 and 1 pair 22 to 18 AWG (0.5 to 1.0 mm ) PELV (Class 2: USA) twisted/ Input 1 shielded for data (see Wiring Diagram). The keypad has now been returned to Factory Settings. System Programming: Programming and activation (addressing) must be accomplished through the HomeWorks QS software. Warranty: For warranty information, please see the Warranty enclosed with the Engraving: Refer to the HomeWorks QS software for engraving instructions. product, or visit www.lutron.com/resiinfo 2 (3) 18 AWG (1.0 mm ) Note: When using the input closures, verify compatibility of external contact * Typical Power Consumption test conditions: all backlights on medium intensity, two LEDs closure input devices. The contact closure inputs can be used with either dry on (two presets active), keypad powered at 24 V . contact closures or ground-referenced solid-state outputs. The outputs must stay in the closed or open states for at least 40 ms in order to be recognized by the keypad. If there is any question as to whether the device is compatible with these specifications, contact the manufacturer. 4. Push all wires back into the wallbox and loosely fasten the control to the wallbox using the keypad mounting screws provided. Do not pinch the wires. See Mounting Diagram. Technical Assistance: U.S.A. / Canada: 1.800.523.9466 Mexico: +1.888.235.2910 Other Countries: +1.610.282.3800 24 hours a day, 7 days a week. Lutron Elec tron ics Co., Inc. Lutron, Homeworks, Claro, Satin Colors, and the sunburst logo are registered trademarks of Lutron Electronics Co., Inc. 7200 Suter Road ©2010 Lutron Electronics Co., Inc. Coopersburg, PA 18036-1299 Print ed in the U.S.A. 10/2010 P/n 043-359 Rev. A